STEERING PAD > DISPOSAL |
| 1. DISPOSE OF STEERING PAD (WHEN INSTALLED IN VEHICLE) |
![]() |
Check the function of SST.
![]() |
Connect SST to the battery. Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.
![]() |
Check the function of SST. Press SST activation switch, and check that the LED of SST activation switch comes on.
Disconnect SST from the battery.
Read the precaution (Click here).
Disconnect the cable from the negative battery terminal.
![]() |
Remove the lower steering column cover.
While turning the steering wheel assembly to the right and left, remove the 2 screws and steering column lower cover.
![]() |
Install SST.
Disconnect the airbag connector (yellow colored) from the spiral cable with steering sensor.
Connect SST connector to the airbag connector of the spiral cable with steering sensor.
![]() |
Move SST at least 10 m (32.8 ft.) away from the vehicle front side window.
Maintaining enough clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.
Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.
Press SST activation switch and deploy the airbag.
| 2. DISPOSE OF STEERING PAD (WHEN NOT INSTALLED IN VEHICLE) |
![]() |
Check the function of SST.
![]() |
Connect SST to the battery. Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.
![]() |
Check the function of SST. Press SST activation switch, and check that the LED of SST activation switch comes on.
Disconnect SST from the battery.
Remove the steering pad (Click here).
![]() |
Using a service-purpose wire harness for the vehicle, tie down the steering pad to the disc wheel.
| Area | Measurement |
| A | 1.25 mm2 or more (0.00193 in.2 or more) |
![]() |
Install the 2 bolts with washers into the 2 bolt holes on the steering pad.
| Area | Specification |
| L | 35.0 mm (1.38 in.) |
| M | 6.0 mm (0.236 in.) |
| Pitch | 1.0 mm (0.0394 in.) |
![]() |
After connecting SST each other, connect them to the steering pad.
![]() |
Wind 3 wire harnesses at least 2 times each around the bolts installed on the left and right sides of the steering pad.
![]() |
Face the airbag deployment side of the steering pad upward. Separately tie the left and right sides of the steering pad to the disc wheel through the hub nut holes. Position SST connector so that it hangs downward through the hub hole of the disc wheel.
![]() |
Install SST.
Connect SST connector.
![]() |
Move SST at least 10 m (32.8 ft.) away from the steering pad tied down to the disc wheel.
![]() |
Cover the steering pad with a cardboard box or tires.
Covering method using a cardboard box:
Cover the steering pad with the cardboard box and place the weights on the cardboard box in 4 places with at least 190 N (19 kgf, 41.9 lbf).
| Area | Measurement |
| X | 460 mm (1.51 ft.) |
| Y | 650 mm (2.13 ft.) |
![]() |
Covering method using tires:
Place at least 3 tires without disc wheels on the tire with disc wheel which the steering pad is tied to. Place the tire with disc wheel on them.
| Area | Measurement |
| Width | 185 mm (7.28 in.) |
| Inner Diameter | 360 mm (1.18 ft.) |
![]() |
Tie the tires together with 2 wire harnesses.
![]() |
Deploy the airbag.
Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.
Check that no one is within a 10 m (32.8 ft.) radius of the disc wheel which the steering pad is tied to.
Press SST activation switch and deploy the airbag.
![]() |
Dispose of the steering pad.
Remove the steering pad from the disc wheel.
Place the steering pad in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.