Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM

WINDOW DEFOGGER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER

E127561E05

  1. Disconnect the H24 air conditioning amplifier connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H24-1 (IG+) - H24-14 (GND)
    P - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    H24-21 (B) - H24-14 (GND)
    R - W-B
    Battery power source
    Always
    11 to 14 V
    H24-14 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the H24 air conditioning amplifier connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H24-11 (CANH) - H24-14 (GND)
    B - W-B
    Hi-level CAN bus line
    Ignition switch ON
    Pulse generation
    (see waveform 1)
    H24-12 (CANL) - H24-14 (GND)
    W - W-B
    Lo-level CAN bus line
    Ignition switch ON
    Pulse generation
    (see waveform 2)
    H24-37 (LIN1) - H24-14 (GND)
    SB - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    H24-38 (RDEF) - H24-14 (GND)
    R - W-B
    Defogger relay
    Ignition switch ON
    Defogger switch OFF
    11 to 14 V
    Ignition switch ON
    Back door window closed
    Defogger switch ON
    Below 1 V

    1. If the result is not as specified, the air conditioning amplifier may have a malfunction.



  5. A086154E10
  6. Waveform 1 (Reference) : Using an oscilloscope
    CAN Communication Signal 
    Terminal Name
    CANH - GND
    Tester Range
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  7. A086155E11
  8. Waveform 2 (Reference) : Using an oscilloscope
    CAN Communication Signal 
    Terminal Name
    CANL - GND
    Tester Range
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.


CHECK INTEGRATION CONTROL AND PANEL

B160782E02

  1. Disconnect the H45 integration control and panel connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H45-16 (IG+) - H45-1 (GND)
    P - W-B
    Ignition power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    H45-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the H45 integration control and panel connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H45-3 (STX) - H45-1 (GND)
    SB - W-B
    LIN communication circuit
    Ignition switch ON
    Pulse generation

    1. If the result is not as specified, the integration control and panel may have a malfunction.