Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Door Courtesy Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives a door open/closed signal from each door courtesy light switch.

WIRING DIAGRAM


E157850E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (DOOR COURTESY LIGHT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Front door courtesy light switch LH signal / ON or OFF
    ON: Front door courtesy light switch LH ON
    OFF: Front door courtesy light switch LH OFF
    -
    P Door Courtesy SW
    Front door courtesy light switch RH signal / ON or OFF
    ON: Front door courtesy light switch RH ON
    OFF: Front door courtesy light switch RH OFF
    -
    RL Door Courtesy SW
    Rear door courtesy light switch LH signal / ON or OFF
    ON: Rear door courtesy light switch LH ON
    OFF: Rear door courtesy light switch LH OFF
    -
    RR Door Courtesy SW
    Rear door courtesy light switch RH signal / ON or OFF
    ON: Rear door courtesy light switch RH ON
    OFF: Rear door courtesy light switch RH OFF
    -
    Result 
    Result
    Proceed to
    OK
    A
    NG (Front door courtesy light switch LH does not operate)
    B
    NG (Front door courtesy light switch RH does not operate)
    C
    NG (Rear door courtesy light switch LH does not operate)
    D
    NG (Rear door courtesy light switch RH does not operate)
    E



B
Go to step 2

C
Go to step 4

D
Go to step 6

E
Go to step 8
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH LH
E142907E15
  1. Remove the front door courtesy light switch LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Not pushed
    Below 1 Ω
    Pushed
    10 kΩ or higher

  1. Reinstall the front door courtesy light switch LH.



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH LH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU)
E146143E04
  1. Disconnect the O8 front door courtesy light switch LH connector.

  1. Disconnect the H4 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O8-1 - H4-24 (DCTY)
    Always
    Below 1 Ω
    O8-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the front door courtesy light switch LH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

4.INSPECT FRONT DOOR COURTESY LIGHT SWITCH RH
E142907E16
  1. Remove the front door courtesy light switch RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Not pushed
    Below 1 Ω
    Pushed
    10 kΩ or higher

  1. Reinstall the front door courtesy light switch RH.



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH RH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU)
E146247E04
  1. Disconnect the P6 front door courtesy light switch RH connector.

  1. Disconnect the H3 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P6-1 - H3-21 (PCTY)
    Always
    Below 1 Ω
    P6-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the front door courtesy light switch RH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

6.INSPECT REAR DOOR COURTESY LIGHT SWITCH LH
E142907E17
  1. Remove the rear door courtesy light switch LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Not pushed
    Below 1 Ω
    Pushed
    10 kΩ or higher

  1. Reinstall the rear door courtesy light switch LH.



NG
REPLACE REAR DOOR COURTESY LIGHT SWITCH LH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU)
E146248E03
  1. Disconnect the O7 rear door courtesy light switch LH connector.

  1. Disconnect the DC main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O7-1 - DC-2 (LCTY)
    Always
    Below 1 Ω
    O7-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the rear door courtesy light switch LH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.INSPECT REAR DOOR COURTESY LIGHT SWITCH RH
E142907E18
  1. Remove the rear door courtesy light switch RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Not pushed
    Below 1 Ω
    Pushed
    10 kΩ or higher

  1. Reinstall the rear door courtesy light switch RH.



NG
REPLACE REAR DOOR COURTESY LIGHT SWITCH RH (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU)
E146249E03
  1. Disconnect the P7 rear door courtesy light switch RH connector.

  1. Disconnect the H3 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P7-1 - H3-25 (RRCY)
    Always
    Below 1 Ω
    P7-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the rear door courtesy light switch RH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU