Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION RECEIVER

NAVIGATION RECEIVER > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 RADIO BRACKET (for SD)


    E232004
  1. Install the bracket with the 4 bolts.

    Torque:
    4.5 N*m{ 45 kgf*cm , 39 in.*lbf }



2. INSTALL NO. 1 RADIO BRACKET (for SD)


    E232003
  1. Install the bracket with the 4 bolts.

    Torque:
    4.5 N*m{ 45 kgf*cm , 39 in.*lbf }



3. INSTALL UPPER INSTRUMENT CLUSTER FINISH PANEL (for SD)


    B229213
  1. Install the upper instrument cluster finish panel with the 4 screws.



4. INSTALL NAVIGATION RECEIVER ASSEMBLY (for SD)
  1. Connect the connectors.



    E232005
  1. Insert the navigation receiver as shown in the illustration to engage the 2 clips on its backside.

    NOTICE:
    When inserting the navigation receiver, do not press the knobs on it.



    E232001
  1. Install the navigation receiver with the 4 bolts.

    Torque:
    8.0 N*m{ 81 kgf*cm , 70 in.*lbf }



5. INSTALL NO. 2 RADIO BRACKET (for DVD)


    B164794
  1. Install the bracket with the 4 bolts.



6. INSTALL NO. 1 RADIO BRACKET (for DVD)


    B164795
  1. Install the bracket with the 4 bolts.



7. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for DVD)
  1. Connect the connectors.



    E159006
  1. Insert the navigation receiver as shown in the illustration to engage the 3 clips on its backside.

    NOTICE:
    When inserting the navigation receiver, do not press the knobs on it.



    B164792
  1. Install the navigation receiver with the 4 bolts.



8. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


I104352
  1. Connect the connectors.

  1. Attach the 4 clips and install the panel.



9. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL
  1. Connect the connectors.

  1. Attach the 4 clips and 2 claws to install the finish panel.



10. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
  1. Attach the 12 clips to install the finish panel.

  1. Connect the 2 connectors and attach the wire harness clamp.

  1. Attach the 4 claws to install the instrument panel finish panel retainer.



11. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    B222976
  1. Connect the connectors.

  1. Attach the 6 clips to install the console panel.

  1. Install the clip.



12. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Attach the 12 clips to install the console panel.



13. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    B167312
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



14. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
  1. Attach the 2 claws to install the sensor.

  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 <A> bolts.



15. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



16. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



17. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.