Home › Vehicle Interior › SEAT › LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Power Seat)

LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Power Seat) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the LH side.



1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Climate Control Seat System)


    B167110
  1. Attach the 3 claws to install the bush.



    B200258
  1. Install the lumbar support adjuster assembly with the 2 screws.

  1. Connect the connector.



    B194042E01
  1. Attach the 4 hooks to install the seatback spring.

  1. Install the 4 springs.



    B232376
  1. Attach the 2 wire harness clamps and connect the connector.



2. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/o Climate Control Seat System)


    B167110
  1. Attach the 3 claws to install the bush.



    B200258
  1. Install the lumbar support adjuster with the 2 screws.

  1. Connect the lumbar support adjuster connector.



    B191028E01
  1. Attach the 6 hooks to install the seatback spring.



3. INSTALL SEATBACK COVER WITH PAD


    B194821E02
  1. Install the seatback cover with pad to the seatback frame.

  1. Lift the seatback cover and, using hog ring pliers, install 4 new hog rings to the seat frame.

  1. Lift the seatback cover, attach the seatback cover bracket to the seat frame, and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure that the side airbag strap is not twisted.



    B194828E01
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install 2 new hog rings to the seat frame.



    B191023
  1. Attach the 3 hooks.



    B194829E01
  1. Using hog ring pliers, install 3 new hog rings to the seat frame.



4. INSTALL FRONT SEAT HEADREST SUPPORT


    B191062E04
  1. Align the protruding portion of the front seat headrest supports with the installation grooves of the front seatback frame.

  1. Attach the 4 claws to install the 2 headrest supports.



5. INSTALL FRONT SEAT CUSHION SHIELD INNER LH


B191015
  1. Attach the 2 claws and clip to install the cushion shield.

  1. Install the screw.



6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    B191256E01
  1. Install the front seat inner belt LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.



    B191249
  1. Connect the connector and engage the 5 clamps.



7. INSTALL FRONT SEAT CUSHION SHIELD LH


    B166945
  1. Connect the switch connectors.

  1. Attach the 2 claws to install the cushion shield.

  1. Install the 3 screws.



    B195226E01
  1. Install the 2 screws.

  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with 2 new hog rings.



8. INSTALL RECLINING POWER SEAT SWITCH KNOB


B201574
  1. Attach the 2 claws to install the knob.



9. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB LH


B201575
  1. Attach the 2 claws to install the knob.



10. INSTALL FRONT SEAT ASSEMBLY LH
  1. Install the front seat assembly (Click here).