Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Accessory Meter does not Illuminate

for Preparation Click here


DESCRIPTION

  1. This circuit provides power to the accessory meter.
  2. The cruise information display of the accessory meter shows the vehicle information input into the combination meter. The display can be changed by using the drive monitor switch.

WIRING DIAGRAM


E163635E02


INSPECTION PROCEDURE

1.CHECK ACCESSORY METER ASSEMBLY
  1. Check the malfunction of the accessory meter.
    Result 
    Result
    Proceed to
    Accessory meter does not display at all
    A
    Cruise information display does not change
    B



B
Go to step 6
A


2.INSPECT FUSE (DOME, ECU-IG NO. 1, ACC)


    B188606E02
  1. Remove the DOME fuse from the engine room relay block.

  1. Remove the ECU-IG No. 1 and ACC fuses from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DOME fuse
    Always
    Below 1 Ω
    ECU-IG No. 1 fuse
    Always
    Below 1 Ω
    ACC fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (ACCESSORY METER - BATTERY AND BODY GROUND)


    E146701E08
  1. Disconnect the I22 accessory meter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I22-22 (ACC) - Body ground
    Ignition switch ACC
    11 to 14 V
    I22-23 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    I22-24 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I22-12 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE ACCESSORY METER ASSEMBLY
  1. Temporarily replace the accessory meter with a new or normally functioning one (Click here).


NEXT


5.CHECK ACCESSORY METER ASSEMBLY (OPERATION)
  1. Check that the accessory meter operation is normal.

    OK:
    Operation of accessory meter returns to normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

END (ACCESSORY METER IS DEFECTIVE) 

6.INSPECT DRIVE MONITOR SWITCH


    E146702E03
  1. Remove the drive monitor switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (MODE) - 5 (E)
    INFO switch pressed
    Below 1 Ω
    INFO switch not pressed
    10 kΩ or higher
    3 (REST) - 5 (E)
    SELECT switch pressed
    Below 1 Ω
    SELECT switch not pressed
    10 kΩ or higher
    4 (SET) - 5 (E)
    SETUP switch pressed
    Below 1 Ω
    SETUP switch not pressed
    10 kΩ or higher



NG
REPLACE DRIVE MONITOR SWITCH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (DRIVE MONITOR SWITCH - COMBINATION METER AND BODY GROUND)


    E146703E03
  1. Disconnect the H37 combination meter connector.

  1. Disconnect the J2 drive monitor switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H37-28 (A/B) - J2-2 (MODE)
    Always
    Below 1 Ω
    H37-28 (A/B) - Body ground
    Always
    10 kΩ or higher
    H37-29 (E) - J2-4 (SET)
    Always
    Below 1 Ω
    H37-29 (E) - Body ground
    Always
    10 kΩ or higher
    H37-30 (RSET) - J2-3 (REST)
    Always
    Below 1 Ω
    H37-30 (RSET) - Body ground
    Always
    10 kΩ or higher
    J2-5 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ACCESSORY METER)


    E146704E06
  1. Disconnect the H37 combination meter connector.

  1. Disconnect the I22 accessory meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H37-31 (TX+) - I22-10 (TX-)
    Always
    Below 1 Ω
    H37-31 (TX+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.REPLACE ACCESSORY METER ASSEMBLY
  1. Temporarily replace the accessory meter with a new or normally functioning one (Click here).


NEXT


10.CHECK ACCESSORY METER ASSEMBLY (OPERATION)
  1. Check that the accessory meter operation is normal.

    OK:
    Operation of accessory meter returns to normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

END (ACCESSORY METER IS DEFECTIVE)