Home › Engine / Hybrid System ยท 3UR-FE › ENGINE CONTROL › AIR FUEL RATIO SENSOR

AIR FUEL RATIO SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)


    A194685
  1. Install the air fuel ratio sensor to the front No. 2 exhaust pipe assembly by hand.



    A194686E01
  1. Using SST, tighten the air fuel ratio sensor.

    SST
    09224-00010  
    1. without SST

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }

    1. with SST

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.



2. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)


    A194685
  1. Install the air fuel ratio sensor to the front exhaust pipe assembly by hand.



    A194686E01
  1. Using SST, tighten the air fuel ratio sensor.

    SST
    09224-00010  
    1. without SST

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }

    1. with SST

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.



3. INSTALL FRONT EXHAUST PIPE ASSEMBLY


A184982
  1. Install a new gasket and the front exhaust pipe assembly to the exhaust manifold RH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the front exhaust pipe assembly to the center exhaust pipe assembly with the 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector and 2 clamps.



4. INSTALL FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY


A184985
  1. Install a new gasket and the front No. 2 exhaust pipe sub-assembly to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the front No. 2 exhaust pipe assembly to the front No. 3 exhaust pipe sub-assembly with the 2 bolts and 2 new nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector and 2 clamps.



5. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.