POWER SEAT SWITCH (for Rear No. 2 Seat) > INSPECTION |
| 1. INSPECT REAR POWER SEAT SWITCH |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (BACK) - 6 (E) | BACK | Below 1 Ω |
| 5 (BACK) - 6 (E) | OFF | 10 kΩ or higher |
| 4 (FWD) - 6 (E) | FWD | Below 1 Ω |
| 4 (FWD) - 6 (E) | OFF | 10 kΩ or higher |
Apply battery voltage to the switch connector, and check that the rear power seat switch illuminates.
| Measurement Condition | Condition | Specified Condition |
| Battery positive (+) → 7 (ILL+) Battery negative (-) → 2 (ILL-) | Always | Illuminates |
| 2. INSPECT FOLD SEAT SWITCH ASSEMBLY (for RH Side) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3 (FOLD) - 5 (E) | FOLD | Below 1 Ω |
| 3 (FOLD) - 5 (E) | OFF | 10 kΩ or higher |
| 4 (RETURN) - 5 (E) | RETURN | Below 1 Ω |
| 4 (RETURN) - 5 (E) | OFF | 10 kΩ or higher |
Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.
| Measurement Condition | Condition | Specified Condition |
| Battery positive (+) → 2 (IND) Battery negative (-) → 5 (E) | Always | Indicator illuminates |
| Battery positive (+) → 1 (+B) Battery negative (-) → 5 (E) | Always | Lettering illuminates |
| 3. INSPECT FOLD SEAT SWITCH ASSEMBLY (for LH Side) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 4 (FOLD) - 3 (E) | FOLD | Below 1 Ω |
| 4 (FOLD) - 3 (E) | OFF | 10 kΩ or higher |
| 5 (RETURN) - 3 (E) | RETURN | Below 1 Ω |
| 5 (RETURN) - 3 (E) | OFF | 10 kΩ or higher |
Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.
| Measurement Condition | Condition | Specified Condition |
| Battery positive (+) → 2 (IND) Battery negative (-) → 3 (E) | Always | Indicator illuminates |
| Battery positive (+) → 1 (+B) Battery negative (-) → 3 (E) | Always | Lettering illuminates |
| 4. INSPECT FOLD SEAT SWITCH ASSEMBLY (for Luggage Compartment RH Seat) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3 (FOLD) - 5 (E) | FOLD | Below 1 Ω |
| 3 (FOLD) - 5 (E) | OFF | 10 kΩ or higher |
| 4 (RETURN) - 5 (E) | RETURN | Below 1 Ω |
| 4 (RETURN) - 5 (E) | OFF | 10 kΩ or higher |
Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.
| Measurement Condition | Condition | Specified Condition |
| Battery positive (+) → 2 (IND) Battery negative (-) → 5 (E) | Always | Indicator illuminates |
| Battery positive (+) → 1 (+B) Battery negative (-) → 5 (E) | Always | Lettering illuminates |
| 5. INSPECT FOLD SEAT SWITCH ASSEMBLY (for Luggage Compartment LH Seat) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 4 (FOLD) - 3 (E) | FOLD | Below 1 Ω |
| 4 (FOLD) - 3 (E) | OFF | 10 kΩ or higher |
| 5 (RETURN) - 3 (E) | RETURN | Below 1 Ω |
| 5 (RETURN) - 3 (E) | OFF | 10 kΩ or higher |
Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.
| Measurement Condition | Condition | Specified Condition |
| Battery positive (+) → 2 (IND) Battery negative (-) → 3 (E) | Always | Indicator illuminates |
| Battery positive (+) → 1 (+B) Battery negative (-) → 3 (E) | Always | Lettering illuminates |