Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL RADIATOR SIDE DEFLECTOR LH


    A215584
  1. Install the deflector with the 6 clips.

  1. Connect the wire harness clamp.



2. INSTALL RADIATOR SIDE DEFLECTOR RH


    A232101E01
  1. Install the deflector with the 6 clips.



3. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH


  1. Install the front No. 2 bumper extension with the 4 nuts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }



    B228055E01



4. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



5. INSTALL FRONT BUMPER REINFORCEMENT


    B194118
  1. Install the front bumper reinforcement with the 6 nuts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }



6. INSTALL LASER RADAR SENSOR (w/ Dynamic Laser Cruise Control System)


E141176

NOTICE:
Do not install the laser radar sensor if it has been damaged or received some sort of shock.

  1. Install the laser sensor with the 3 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



7. INSTALL FRONT BUMPER END RETAINER LH


    B194117
  1. Install the front bumper end retainer with the 3 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



8. INSTALL FRONT BUMPER END RETAINER RH

HINT:
Use the same procedure described for the LH side.



9. INSTALL FRONT UPPER CENTER BUMPER RETAINER


    B194116
  1. Install the front upper center bumper retainer with the 6 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



10. INSTALL FRONT BUMPER SIDE SUPPORT LH


    B194115
  1. Attach the 3 claws to install the front bumper side support.

  1. Install the 2 screws.



11. INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure described for the LH side.



12. INSTALL CLIP


    B194123
  1. Install the clip.

    HINT:
    Use the same procedure for all clips.



13. INSTALL FRONT FENDER LINER BRACKET LH


    B194119
  1. Attach the 2 claws to install the front fender liner bracket.



14. INSTALL FRONT FENDER LINER BRACKET RH

HINT:
Use the same procedure described for the LH side.



15. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)


    E146465E01
  1. Install the ultrasonic sensor retainer to the front bumper.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.



16. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)


    E146466
  1. Engage the 2 claws and install the ultrasonic sensor.

  1. Connect the sensor connector.



17. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)


    E161819
  1. Engage the 2 claws and install the fog light.



18. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure described for the LH side.



19. INSTALL FOG LIGHT MOUNTING BRACKET LH (w/ Fog Light)


    E161818
  1. Install the fog light mounting bracket with the 3 bolts.



20. INSTALL FOG LIGHT MOUNTING BRACKET RH (w/ Fog Light)

HINT:
Use the same procedure described for the LH side.



21. INSTALL FOG LIGHT COVER LH


    B194122
  1. Attach the 6 claws to install the fog light cover.



22. INSTALL FOG LIGHT COVER RH

HINT:
Use the same procedure described for the LH side.



23. INSTALL FRONT BUMPER GARNISH
  1. Attach the 17 claws to install the front bumper garnish.



  1. Install the 6 clips.


    B228054E01