Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM

POWER BACK DOOR SYSTEM > Power Back Door Warning System does not Operate

for Preparation Click here


DESCRIPTION

When the power back door warning system does not operate, one of the following may be malfunctioning: 1) power back door warning buzzer circuit, 2) wireless door lock control system, 3)power back door drive unit (power back door ECU) or 4) Main Body ECU.

HINT:
Since the power back door control system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure


WIRING DIAGRAM


B165222E06


INSPECTION PROCEDURE

1.CHECK OPERATION
  1. Check the power back door system operation.
    Result 
    Result
    Proceed to
    Power back door functions but the power back door warning buzzer does not operate.
    A
    Power back door functions but the hazard warning light does not come on.
    B
    Power back door functions but the power back door warning buzzer in the power back door ECU does not operate.
    C



B
Go to step 6

C
REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Back Door / Active Test /

  1. According to the display on the Techstream, perform the Active Test.

    Back Door 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    PBD Buzzer
    Power back door buzzer sound
    ON/OFF
    -

    OK:
    Buzzer sounds normally.



NG
Go to step 3
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)  

3.REPLACE POWER BACK DOOR WARNING BUZZER
  1. Temporarily replace the power back door buzzer with a new or normally functioning one (Click here).


NEXT


4.CHECK POWER BACK DOOR WARNING BUZZER (OPERATION)
  1. Check that the buzzer sounds operation.

OK:
The buzzer sounds.

NOTICE:
When battery voltage is directly applied to the buzzer does not sound.



NG
Go to step 5
OK

END 

5.CHECK HARNESS AND CONNECTOR (WARNING BUZZER - BACK DOOR ECU AND GROUND)


    B165206E04
  1. Disconnect the V13 buzzer connector.

  1. Disconnect the O30 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V13-1 - O30-26 (BZR+)
    Always
    Below 1 Ω
    V13-2 - Body ground
    Always
    Below 1 Ω
    V13-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the buzzer connector.

  1. Reconnect the ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)  

6.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM (HAZARD ANSWER-BACK FUNCTION)
  1. Check the wireless door lock operation.

    OK:
    Hazard answer-back function operates normally.



NG
GO TO OTHER FLOW CHART (NO ANSWER - BACK) (Click here)
OK


7.REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Replace the power back door drive unit (power back door ECU) (Click here).


NEXT


8.CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Check that the power back door warning buzzer operates normally.

    OK:
    It operates normally.



NG
REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
OK

END (POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) DEFECTIVE)