Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › RELAY

RELAY > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT CIRCUIT OPENING RELAY (C/OPN)


    A184106E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the circuit opening relay.



2. INSPECT INTEGRATION RELAY (IG2)
  1. Measure the resistance of the IG2 MAIN fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      IG2 MAIN fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the IG2 MAIN fuse.



    A106666E15
  1. Measure the resistance of the ignition relay No. 2 (IG2) circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-8
      Battery voltage is not applied to terminals 1B-6 and 1B-7
      10 kΩ or higher
      Battery voltage is applied to terminals 1B-6 and 1B-7
      Below 1 Ω

      If the result is not as specified, replace the integration relay.



3. INSPECT INTEGRATION RELAY (EFI)
  1. Measure the resistance of the EFI No. 1 fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI No. 1 fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the EFI No. 1 fuse.



    A106666E15
  1. Measure the resistance of the EFI MAIN relay circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-4
      Battery voltage is not applied to terminals 1B-2 and 1B-3
      10 kΩ or higher
      Battery voltage is applied to terminals 1B-2 and 1B-3
      Below 1 Ω

      If the result is not as specified, replace the integration relay.



4. INSPECT INTEGRATION RELAY (A/F)
  1. Measure the resistance of the A/F fuse.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A/F fuse
      Always
      Below 1 Ω

      If the result is not as specified, replace the A/F fuse.



    A106666E16
  1. Measure the resistance of the A/F sensor heater relay circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1A-4
      Battery voltage is not applied to terminals 1A-2 and 1A-3
      10 kΩ or higher
      Battery voltage is applied to terminals 1A-2 and 1A-3
      Below 1 Ω

      If the result is not as specified, replace the integration relay.



5. INSPECT FUEL PUMP RELAY (F/PMP)


    A184106E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the fuel pump relay.



6. INSPECT FUEL PRESSURE CONTROL VALVE RELAY (F/PMP VSV)


    A184106E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the fuel pump control valve relay.



7. INSPECT AIR PUMP HEATER RELAY (AI-HTR)


    A184106E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the air pump heater relay.