Home › Vehicle Interior › HEATING / AIR CONDITIONING › BLOWER MOTOR CONTROLLER (for Rear Side)

BLOWER MOTOR CONTROLLER (for Rear Side) > REMOVAL

for Preparation Click here



1. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


B190118
  1. Raise the handle, disengage the 4 guides and remove the No. 2 deck board.



2. REMOVE LUGGAGE COMPARTMENT TRIM BOX


B194633
  1. Remove the 4 caps.



    B190116
  1. Remove the 4 bolts and luggage compartment trim box.



3. REMOVE ROPE HOOK ASSEMBLY


B191405
  1. Remove the bolt and rope hook.

    HINT:
    Use the same procedure for both sides.



4. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY


B190117
  1. Disengage the 5 clips and remove the No. 1 deck board.



5. REMOVE DECK BOARD REINFORCEMENT SUB-ASSEMBLY


B190120
  1. Remove the 4 bolts and deck board reinforcement.



6. REMOVE DECK BOARD BRACKET


B190119
  1. Remove the 2 bolts and deck board bracket.



7. REMOVE SEAT TRACK BRACKET FRONT COVER OUTER


    B191196E02
  1. Detach the 2 claws and 2 guides in the order shown in the illustration, and then remove the seat track bracket front cover outer.



8. REMOVE SEAT TRACK BRACKET FRONT COVER INNER


    B232092E01
  1. Detach the claw and clip and 2 guides in the order shown in the illustration, and then remove the seat track bracket front cover inner.



9. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat)


    B191200
  1. Remove the 2 bolts.



    B191203
  1. Remove the 2 bolts.

  1. Remove the connector.

  1. Remove the rear No. 2 seat assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



10. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat)


    B191200
  1. Remove the 2 bolts.



    B191201
  1. Remove the 2 bolts.

  1. Remove the rear No. 2 seat assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



11. REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH


B191794
  1. Disengage the 2 clips and 5 claws, and remove the rear seat cushion hinge lower cover.



12. REMOVE REAR FLOOR STEP NO. 1 COVER


B191403E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



13. REMOVE REAR FLOOR STEP NO. 2 COVER


B193052E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



14. REMOVE REAR DOOR SCUFF PLATE RH


B186665
  1. Remove the bolt.

  1. Disengage the 5 clips and the 6 claws and 2 guides, and remove the rear door scuff plate front side.



    B186666
  1. Remove the 2 bolts.

  1. Disengage the 5 clips and 2 claws, and remove the scuff plate rear side.



15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


B191804
  1. Remove the rear door opening trim weatherstrip.



16. REMOVE ROPE HOOK ASSEMBLY


B190140E01

HINT:
Use the same procedure for both sides.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.



    B190141
  1. Remove the bolt and rope hook.



17. REMOVE REAR FLOOR MAT SUPPORT PLATE


B190142
  1. Disengage the 5 clips and 4 claws, and remove the rear floor mat support plate.



18. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Standard)


B190145
  1. Disengage the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Disengage the 11 clips.



  1. Disconnect the connector and remove the quarter trim panel.


    B219907



19. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)


B190145
  1. Disengage the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Disengage the 11 clips.



  1. Disconnect the 3 connectors and remove the quarter trim panel.


    B222459



20. REMOVE BLOWER MOTOR CONTROL


I104446
  1. Disconnect the connector.

  1. Remove the 2 screws and the blower motor control.