Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)

REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY


    B194032
  1. Install the rear No. 2 seat rod sub-assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



2. INSTALL POWER SEAT MOTOR ASSEMBLY LH


    B201580
  1. Fully rotate both lower arms in the seat folded direction as shown in the illustration.

    NOTICE:
    If the motor is installed with the lower arms at an intermediate position, the motor initial position will not match the seat position, so that when the seat is operated the position will be incorrect.



    B201581
  1. Install the power seat motor assembly LH with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



3. INSTALL POWER SEAT MOTOR ASSEMBLY RH


    B201582
  1. Install the power seat motor assembly RH with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    B201583
  1. Using a screwdriver and hammer, lightly tap the reclining connecting pipe to install it.

  1. Install the 2 washers.

    NOTICE:
    When the reclining connecting pipe extends about the same distance left and right, install the 2 washers.



    B201584
  1. Hold the reclining connecting pipe with pliers or similar tool and rotate the reclining connecting pipe and arms to the position shown in the illustration.



4. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH


    B293206
  1. Install the No. 3 seatback frame sub-assembly LH with the 3 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



5. INSTALL RECLINING CONTROL BASE LH


    B194027
  1. Install the reclining control base LH with the 2 nuts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



6. INSTALL REAR NO. 2 SEAT WIRE LH


    B293205
  1. Attach the 5 wire harness clamps.

  1. Connect the 3 connectors to install the rear No. 2 seat wire LH.



7. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH


    B194023E01
  1. Using hog ring pliers, install the No. 2 seatback cover sub-assembly LH to the No. 2 seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



8. INSTALL SEATBACK COVER WITH PAD


    B194020E01
  1. Attach the clip to install the rear seat belt hook.

  1. Using hog ring pliers, install the seatback cover with pad to the No. 3 seatback frame sub-assembly LH with a new hog ring.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B288985
  1. Attach the hooks.

  1. Attach the 2 wire harness clamps.



9. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY


    B290086
  1. Attach the 8 claws to install the 4 rear No. 2 seat headrest supports.



10. INSTALL REAR SEAT HEADREST ASSEMBLY


B290078
  1. Install the rear seat headrest assembly.

    NOTICE:
    1. Make sure the rear seat headrest assembly is facing in the correct direction.
    2. Push in the rear seat headrest assembly until the headrest lock engages.



    B288834E01
  1. Insert the cable end into the reclining control base LH.

  1. Twist the cable end in the direction indicated by the arrow to connect it and attach the cable clamp.

  1. Connect the headrest cable to the No. 3 seatback frame sub-assembly LH with the cable clamp.



    B288835
  1. Attach the hook to connect the lower part of the No. 2 seatback cover sub-assembly LH.



11. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH


    B290081
  1. Attach the 12 clips to install the rear seatback board sub-assembly LH.



12. INSTALL REAR NO. 2 SEATBACK COVER LH


    B195227
  1. Attach the 3 claws to install the rear No. 2 seatback cover LH.



13. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
  1. Install the rear center seat headrest assembly.



14. INSTALL REAR SEAT CUSHION COVER LH


    B194006
  1. Attach the claw.

  1. Install the rear seat cushion cover LH with the screw.



15. INSTALL REAR SEAT CUSHION COVER INNER RH


    B194007
  1. Attach the claw.

  1. Install the rear seat cushion cover inner RH with the screw.



16. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH


    B194005E01
  1. Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



17. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY LH


    B194003
  1. Set the No. 3 seat cushion spring assembly LH in place.

  1. Attach the hooks.



    B194002E01
  1. Using hog ring pliers, install the No. 3 seat cushion spring assembly LH with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



18. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH


B194000
  1. Install the 2 bushes to the No. 3 seat cushion spring assembly LH. Then using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the rear No. 2 seat cushion assembly LH with the 2 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



19. INSTALL REAR SEAT LOCK COVER OUTER LH


    B193996
  1. Attach the 2 claws.

  1. Install the rear seat lock cover outer LH with the screw.



20. INSTALL REAR SEAT LOCK COVER INNER RH


    B193998
  1. Attach the 3 claws.

  1. Install the rear seat lock cover inner RH with the screw.



21. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH


    B193995
  1. Install the rear No. 2 seat inner belt assembly.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193994
  1. Install the 2 clips.