Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type RH Side)

REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type RH Side) > REASSEMBLY

for Preparation Click here


NOTICE:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY


    B191244
  1. Install the rear No. 2 seat rod sub-assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



2. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY RH


    B191240
  1. Install the No. 3 seatback frame sub-assembly RH with the 5 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



3. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY


    B191238
  1. Insert the rear No. 1 seat lock cable assembly through the No. 3 seatback frame sub-assembly RH.

  1. Insert and rotate the cable ends to connect them.

  1. Connect the 2 clamps.

  1. Attach the 3 cable ties to install the rear No. 1 seat lock cable assembly.



4. INSTALL REAR SEAT RECLINING COVER INNER LH


    B191236
  1. Attach the claw.

  1. Install the rear seat reclining cover inner LH with the screw.



5. INSTALL REAR SEAT RECLINING COVER INNER RH


    B191235
  1. Attach the claw.

  1. Install the rear seat reclining cover inner RH with the screw.



6. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY RH


    B191232E01
  1. Using hog ring pliers, install the No. 2 seatback cover sub-assembly RH to the No. 2 seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



7. INSTALL SEATBACK COVER WITH PAD


    B191227
  1. Attach the hooks to install the seatback cover with pad.



    B195219
  1. Attach the hooks.



8. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY


B290096
  1. Attach the 4 claws to install the 2 rear No. 2 seat headrest supports.



9. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH


    B292871
  1. Attach the 9 clips to install the rear seatback board sub-assembly RH.



10. INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B191220E01
  1. Connect the rear No. 1 seat lock cable assembly to the rear back lock control lever sub-assembly RH in the order shown in the illustration.

  1. Install the rear back control lever sub-assembly RH with the screw.



11. INSTALL REAR NO. 2 SEAT HANDLE


    B191219E01
  1. Connect the rear No. 1 seat lock cable assembly to the rear No. 2 seat handle in the order shown in the illustration.

  1. Install the rear No. 2 seat handle with the 2 screws.



12. INSTALL REAR SEAT HEADREST ASSEMBLY


B290080
  1. Install the rear seat headrest assembly.

    NOTICE:
    1. Make sure the rear seat headrest assembly is facing in the correct direction.
    2. Push in the rear seat headrest assembly until the headrest lock engages.



13. INSTALL REAR SEAT CUSHION COVER LH


    B191218
  1. Attach the claw.

  1. Install the rear seat cushion cover LH with the screw.



14. INSTALL REAR SEAT CUSHION COVER OUTER RH


    B191217
  1. Attach the claw.

  1. Install the rear seat cushion cover outer RH with the screw.



15. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH


    B191216E02
  1. Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly RH to the No. 2 seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



16. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY RH


    B191214
  1. Set the No. 3 seat cushion spring assembly RH in place.

  1. Attach the hooks.



    B191213E01
  1. Using hog ring pliers, install the No. 3 seat cushion spring assembly RH with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



17. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY RH


B191211
  1. Install the 2 bushes to the No. 3 seat cushion spring assembly RH. Then using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the rear No. 2 seat cushion assembly RH with the 2 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



18. INSTALL REAR SEAT LOCK COVER INNER LH


    B191207
  1. Attach the 3 claws.

  1. Install the rear seat lock cover inner LH with the screw.



19. INSTALL REAR SEAT LOCK COVER OUTER RH


    B191209
  1. Attach the 2 claws.

  1. Install the rear seat lock cover outer RH with the screw.



20. INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY


    B191206
  1. Install the rear No. 2 seat inner belt sub-assembly.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191205
  1. Install the 2 clips.