REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side) > REASSEMBLY |
| 1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY |
![]() |
Install the rear No. 2 seat rod sub-assembly with the 2 bolts.
| 2. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH |
![]() |
Install the No. 3 seatback frame sub-assembly LH with the 5 bolts.
| 3. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY |
![]() |
Insert the rear No. 1 seat lock cable assembly through the No. 3 seatback frame sub-assembly.
Insert and rotate the cable ends to connect them.
Connect the 2 clamps.
Attach the 3 cable ties to install the rear No. 1 seat lock cable assembly.
| 4. INSTALL REAR SEAT RECLINING COVER INNER LH |
![]() |
Attach the claw.
Install the rear seat reclining cover inner LH with the screw.
| 5. INSTALL REAR SEAT RECLINING COVER INNER RH |
![]() |
Attach the claw.
Install the rear seat reclining cover inner RH with the screw.
| 6. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH |
![]() |
Using hog ring pliers, install the No. 2 seatback cover sub-assembly LH to the No. 2 seatback pad with new hog rings.
| 7. INSTALL SEATBACK COVER WITH PAD |
![]() |
Attach the clip to install the rear seat belt hook.
Using hog ring pliers, install the seatback cover with pad to the seatback frame with a new hog ring.
![]() |
Attach the hooks.
![]() |
Attach the hooks.
| 8. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Attach the 8 claws to install the 4 rear No. 2 seat headrest supports.
| 9. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH |
![]() |
Attach the 12 clips to install the rear seatback board sub-assembly LH.
| 10. INSTALL REAR NO. 2 SEATBACK COVER LH |
![]() |
Attach the 3 claws to install the rear No. 2 seatback cover LH.
| 11. INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH |
![]() |
Connect the rear No. 1 seat lock cable assembly in the order shown in the illustration to install the rear back lock control lever sub-assembly RH.
Install the rear back lock control lever sub-assembly RH with the screw.
| 12. INSTALL REAR NO. 2 SEAT HANDLE |
![]() |
Connect the rear No. 1 seat lock cable assembly to the rear No. 2 seat handle in the order shown in the illustration.
Install the rear No. 2 seat handle with the 2 screws.
| 13. INSTALL REAR SEAT HEADREST ASSEMBLY |
![]() |
Install the rear seat headrest assembly.
| 14. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
Install the rear center seat headrest assembly.
| 15. INSTALL REAR SEAT CUSHION COVER LH |
![]() |
Attach the claw.
Install the rear seat cushion cover LH with the screw.
| 16. INSTALL REAR SEAT CUSHION COVER INNER RH |
![]() |
Attach the claw.
Install the rear seat cushion cover inner RH with the screw.
| 17. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH |
![]() |
Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion pad with new hog rings.
| 18. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY LH |
![]() |
Set the No. 3 seat cushion spring assembly LH in place.
Attach the hooks.
![]() |
Using hog ring pliers, install the No. 3 seat cushion spring assembly LH with new hog rings.
| 19. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH |
![]() |
Install the 2 bushes to the No. 3 seat cushion spring assembly LH. Then using a T45 "TORX" socket wrench, install the 2 "TORX" bolts.
Install the rear No. 2 seat cushion assembly LH with the 2 bolts.
| 20. INSTALL REAR SEAT LOCK COVER OUTER LH |
![]() |
Attach the 2 claws.
Install the rear seat lock cover outer LH with the screw.
| 21. INSTALL REAR SEAT LOCK COVER INNER RH |
![]() |
Attach the 3 claws.
Install the rear seat lock cover inner RH with the screw.
| 22. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH |
![]() |
Install the rear No. 2 seat inner belt assembly.
![]() |
Install the 2 clips.