Home › Vehicle Interior › SEAT BELT › REAR NO. 1 SEAT OUTER BELT ASSEMBLY

REAR NO. 1 SEAT OUTER BELT ASSEMBLY > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the RH side.



1. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat)
  1. Remove the rear No. 2 seat assembly (Click here).



2. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat)
  1. Remove the rear No. 2 seat assembly (Click here).



3. REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH


B191794
  1. Disengage the 2 clips and 5 claws, and remove the rear seat cushion hinge lower cover.



4. REMOVE REAR FLOOR STEP NO. 1 COVER


B191403E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



5. REMOVE REAR FLOOR STEP NO. 2 COVER


B193052E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



6. REMOVE REAR DOOR SCUFF PLATE RH


B186665
  1. Remove the bolt.

  1. Disengage the 5 clips and the 6 claws and 2 guides, and remove the rear door scuff plate front side.



    B186666
  1. Remove the 2 bolts.

  1. Disengage the 5 clips and 2 claws, and remove the scuff plate rear side.



7. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


B191804
  1. Remove the rear door opening trim weatherstrip.



8. REMOVE ROPE HOOK ASSEMBLY


B190140E01

HINT:
Use the same procedure for both sides.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.



    B190141
  1. Remove the bolt and rope hook.



9. REMOVE REAR FLOOR MAT SUPPORT PLATE


B190142
  1. Disengage the 5 clips and 4 claws, and remove the rear floor mat support plate.



10. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Manual Seat)


B190145
  1. Disengage the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Disengage the 11 clips.



  1. Disconnect the connector and remove the quarter trim panel.


    B219907



11. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)


B190145
  1. Disengage the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Disengage the 11 clips.



  1. Disconnect the 3 connectors and remove the quarter trim panel.


    B222459



12. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH


B190121E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the cover.



    B190124
  1. Remove the bolt.

  1. Detach the 5 clips.

  1. Pass the rear seat outer belt floor anchor through the rear window side garnish, and remove the rear window side garnish.



13. REMOVE REAR SIDE NO. 2 AIR DUCT


    E188149
  1. Remove the 2 clips and the air duct.



14. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH


    B194784
  1. Remove the bolt.



    B194785
  1. Remove the 2 bolts and rear No. 1 seat outer belt assembly.



15. REMOVE REAR NO. 1 SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    B194786
  1. Remove the 2 bolts and rear No. 1 shoulder belt anchor adjuster assembly.