REAR CENTER SEAT OUTER BELT ASSEMBLY (for Rear No. 1 Seat) > INSTALLATION |
| 1. INSTALL CENTER SEAT OUTER BELT ASSEMBLY |
![]() |
Align the center seatback frame claws with the center seat outer belt retractor positioning holes.
Install the center seat outer belt assembly with the 4 nuts.
Engage the cable with the cable tie.
| 2. INSTALL SEATBACK COVER WITH PAD |
![]() |
Attach the hooks to install the seatback cover with pad.
![]() |
Attach the hooks.
![]() |
Using hog ring pliers, install the center seatback cover to the center seatback frame with 6 new hog rings.
![]() |
Using hog ring pliers, install the center seatback cover to the center seatback frame with 5 new hog rings.
| 3. INSTALL ARMREST ASSEMBLY |
![]() |
Install the armrest assembly with the 2 nuts.
| 4. INSTALL REAR SEAT SHOULDER BELT HOLE COVER NO. 3 |
![]() |
Attach the 2 claws, to the rear seat shoulder belt hole cover.
Install the rear seat shoulder belt hole cover with the 2 screws.
| 5. INSTALL REAR SEAT HEADREST SUPPORT |
![]() |
Align the protruding portion of the rear seat headrest supports with the installation grooves of the center seatback frame.
Attach the 4 claws to install the 2 rear seat headrest supports.
| 6. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH |
![]() |
Connect the cable in the order shown in the illustration to install the rear seat lock control lever sub-assembly.
Install the rear seat lock control lever sub-assembly with the 2 screws.
| 7. INSTALL REAR SEATBACK LOCK STRIKER COVER |
![]() |
Attach the guide and claw to install the rear seatback lock striker cover.
| 8. INSTALL REAR SEAT SHOULDER BELT HOLE COVER NO. 2 |
![]() |
Using a T30 "TORX" socket, install the rear seat shoulder belt hole cover with the 2 "TORX" bolts.
| 9. INSTALL REAR SEATBACK LOCK BEZEL UPPER |
![]() |
Install the rear seatback lock bezel upper with the 2 screws.
![]() |
Install the center seat outer belt lower bolt.
| 10. INSTALL REAR SEAT SHOULDER BELT HOLE COVER NO. 1 |
![]() |
Attach the 4 claws to install the rear seat shoulder belt hole cover.
| 11. INSTALL REAR SEAT CUSHION UNDER COVER |
![]() |
Install the rear seat cushion under cover with the 2 screws.
| 12. INSTALL CENTER SEAT HINGE COVER RH |
![]() |
Attach the 3 claws and clip to install the center seat hinge cover.
Install the screw.
| 13. INSTALL CENTER SEAT HINGE COVER LH |
![]() |
Attach the 3 claws and clip to install the center seat hinge cover.
Install the screw.
| 14. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY |
![]() |
Attach the 6 clips to install the rear seatback board sub-assembly.
| 15. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
| 16. INSTALL CENTER SEAT CUSHION ASSEMBLY |
![]() |
Install the 2 bushes to the cushion spring. Then, using a T45 "TORX" socket, install the 2 "TORX" bolts.
Install the 2 bolts.
![]() |
Attach the hook and loop fastener and hook.
Pass the inner belt through the hole of the seat cushion.
| 17. INSTALL REAR SEAT CUSHION HINGE COVER UPPER RH |
![]() |
Attach the 2 claws to install the rear seat cushion hinge cover upper.
Install the screw.
Attach the hook.
| 18. INSTALL REAR SEAT CUSHION HINGE COVER UPPER LH |
![]() |
Attach the 2 claws to install the rear seat cushion hinge cover upper.
Install the screw.
Attach the hook.
| 19. INSTALL REAR CENTER SEAT ASSEMBLY |
Install the rear center seat assembly (Click here).