Home › Engine / Hybrid System · 3UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P144C    Open in Secondary Air Injection System Heater Control Circuit

DTC    P144D    Short in Secondary Air Injection System Heater Control Circuit

for Preparation Click here


DESCRIPTION

The ECM operates the air pump heater relay which causes the air pump heater to operate.

DTC No.
DTC Detection Condition
Trouble Area
P144C
Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
  1. Open or short in air pump heater relay circuit
  2. Air pump heater relay
  3. ECM
P144D
Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
  1. Open or short in air pump heater relay circuit
  2. Air pump heater relay
  3. ECM

MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the air pump heater relay circuit. When the system is normal, the battery voltage is applied to terminal HAI1 of the ECM while the air pump heater relay is turned off, and the battery voltage is not applied to terminal HAI1 of the ECM while the air pump heater relay is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.
  1. The battery voltage is not applied to terminal HAI1 while the air pump heater relay is off.
  2. The battery voltage is applied to terminal HAI1 while the air pump heater relay is on.

MONITOR STRATEGY


Related DTCs
P144C: Air pump heater relay circuit range check (Low voltage)
P144D: Air pump heater relay circuit range check (High voltage)
Required Sensors/Components (Main)
Air pump heater relay
Required Sensors/Components (Related)
-
Frequency of operation
Continuous
Duration
5 second
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
All of following conditions met
-
Battery
8 V or more
Ignition switch
ON
Starter
OFF
Time after ignition switch off to ON
more than 0.5 seconds

TYPICAL MALFUNCTION THRESHOLDS


Low voltage: 
Air pump heater relay output terminal voltage
Low

High voltage: 
Air pump heater relay output terminal voltage
High

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT AIR PUMP HEATER RELAY
  1. Inspect the air pump heater relay .



NG
REPLACE AIR PUMP HEATER RELAY
OK


2.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)
  1. Remove the air pump heater relay.



    A258729E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Air pump heater relay terminal 2 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reinstall the air pump heater relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER RELAY)
  1. Remove the air pump heater relay.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Air pump heater relay terminal 1 - D56-61 (HAI1)
    Always
    Below 1 Ω

    Standard resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Air pump heater relay terminal 1 or D56-61 (HAI1) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the air pump heater relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)