Home › Audio/Visual/Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

BLIND SPOT MONITOR SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.

  5. Read the Data List according to the display on the Techstream.

    Blind Spot Monitor Master 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    BSM Main Switch
    Blind spot monitor main switch assembly (warning canceling switch assembly) / OFF or ON
    ON: Blind spot monitor main switch assembly (warning canceling switch assembly) on
    OFF: Blind spot monitor main switch assembly (warning canceling switch assembly) off
    -
    Master Side Turn Switch
    Master side turn switch / OFF or ON
    ON: Right turn switch on
    OFF: Right turn switch off
    This item is always OFF for vehicles which send and receive this signal via CAN communication.
    Signal Noise Ratio(Tilt:ch1)
    Target radar emission received by narrow-angle antenna / Min.: 0 db, Max.: 249 db
    Depends on settings (Initial value 0 dB)
    This item is not supported.
    BSM Warning Indicator Turning on(Master)
    Blind spot monitor indicator RH illumination state / OFF or ON
    1. OFF: Except below
    2. ON: All of following conditions met
      1. Initial check not being performed
      2. Vehicle detected in right side warning area
      3. Right turn signal off
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever not in R
      6. Blind spot monitor system warning message not displayed
    -
    BSM Warning Indicator Flashing(Master)
    Blind spot monitor indicator RH flashing state / OFF or ON
    1. OFF: Except below
    2. ON: All of following conditions met
      1. Initial check not being performed
      2. Vehicle detected in right side warning area
      3. Right turn signal off
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever not in R
      6. Blind spot monitor system warning message not displayed
    -
    Turn Switch State
    Master side, slave side state of the turn switch / Master ON, Slave ON or OFF
    Master ON: Right turn switch on
    Slave ON: Left turn switch on
    OFF: Switch not operated
    -
    Master Side Turn Signal
    State of the master side turn signal / OFF or ON
    ON: Right turn signal received
    OFF: Right turn signal not received
    -
    Reverse
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/ h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering angle sensor / Min.: - 3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    VGRS Relative Angle
    Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad
    Left turn: Increases
    Right turn: Decreases
    This item is only for vehicles with the VGRS system.
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    11 to 14 V
    -
    HV Flag
    Hybrid vehicle / OFF or ON
    OFF: Non-hybrid vehicle
    ON: Hybrid vehicle
    -
    VGRS Flag
    VGRS installed / OFF or ON
    OFF: VGRS not installed
    ON: VGRS installed
    -
    BSM Main SW Inspection Completeness Flag
    Completion of inspection for blind spot monitor main switch (warning canceling assembly) / Incompl or Compl
    Incompl: Inspection not completed
    Compl: Inspection completed
    Changes to Compl when the blind spot monitor main switch (warning canceling assembly) is changed from off to on during Test Mode.
    Beam Axis Inspection Completeness Flag
    Completion of beam axis inspection / Incompl or Compl
    Incompl: Inspection not completed
    Compl: Inspection completed
    Changes to Compl when Test Mode has been entered.
    Destination Undefined Flag
    Destination determination / Unfixed or Fixed
    Unfixed: Destination information for sensor undetermined
    Fixed: Destination information for sensor verified by CAN destination information
    -
    Number of DTC
    Number of DTCs / Min.: 0, Max.: 255
    When system normal: 0
    When malfunction detected: More than 0
    -

    Blind Spot Monitor Slave 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Slave Side Turn Switch
    Slave side turn switch / OFF or ON
    ON: Left turn switch on
    OFF: Left turn switch off
    This item is always OFF for vehicles which send and receive this signal via CAN communication.
    BSM Warning Indicator Turning on(Slave)
    Blind spot monitor indicator LH illumination state / OFF or ON
    1. OFF: Except below
    2. ON: All of following conditions met
      1. Initial check not being performed
      2. Vehicle detected in left side warning area
      3. Left turn signal off
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever not in R
      6. Blind spot monitor system warning message not displayed
    -
    BSM Warning Indicator Flashing(Slave)
    Blind spot monitor indicator LH flashing state / OFF or ON
    1. OFF: Except below
    2. ON: All of following conditions met
      1. Initial check not being performed
      2. Vehicle detected in left side warning area
      3. Left turn signal off
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever not in R
      6. Blind spot monitor system warning message not displayed
    -
    Turn Switch State
    Master side, slave side state of the turn switch / Master ON, Slave ON or OFF
    Master ON: Right turn switch on
    Slave ON: Left turn switch on
    OFF: Switch not operated
    -
    Slave Side Turn Signal
    State of the slave side turn signal / OFF or ON
    ON: Left turn signal received
    OFF: Left turn signal not received
    -
    Reverse
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/ h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering angle sensor / Min.: - 3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    VGRS Relative Angle
    Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad
    Left turn: Increases
    Right turn: Decreases
    This item is only for vehicles with the VGRS system.
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    11 to 14 V
    -
    HV Flag
    Hybrid vehicle / OFF or ON
    OFF: Non-hybrid vehicle
    ON: Hybrid vehicle
    -
    VGRS Flag
    VGRS installed / OFF or ON
    OFF: VGRS not installed
    ON: VGRS installed
    -
    Beam Axis Inspection Completeness Flag
    Completion of beam axis inspection / Incompl or Compl
    Incompl: Inspection not completed
    Compl: Inspection completed
    Changes to Compl when Test Mode has been entered.
    Destination Undefined Flag
    Destination determination / Unfixed or Fixed
    Unfixed: Destination information for sensor undetermined
    Fixed: Destination information for sensor verified by CAN destination information
    -
    Number of DTC
    Number of DTCs / Min.: 0, Max.: 255
    When system normal: 0
    When malfunction detected: More than 0
    -