VEHICLE STABILITY CONTROL SYSTEM > SYSTEM DESCRIPTION |
| SYSTEM DESCRIPTION |
ABS (Anti-lock Brake System)
The ABS helps prevent the wheels from locking when the brakes are applied firmly or on a slippery surface.

Operation description
The skid control ECU detects wheel lock conditions by receiving vehicle speed signals from each speed sensor, and sends control signals to the pump motor and solenoid valve to prevent the wheels from locking by controlling the brake fluid pressure of each wheel cylinder.
When the ABS system malfunctions, the ABS warning light and slip indicator light come on and the VSC OFF indicator light blinks.
EBD (Electronic Brake Force Distribution)
The EBD control utilizes the ABS, performing proper brake force distribution between the front and rear wheels in accordance with the driving conditions. When the brakes are applied while cornering, it also controls the braking forces of the rear right and rear left wheels, helping to maintain vehicle stability.

Operation description
The skid control ECU receives speed signals from each speed sensor to detect the slip conditions of the wheels and sends control signals to the solenoid.
The solenoid valve controls the brake fluid pressure of each wheel cylinder, and divides the control power properly between the front and rear wheels and the rear right and rear left wheels.
The ABS and brake warning lights and slip indicator light come on and the VSC OFF indicator light blinks to indicate malfunctions in the EBD system.
BA (Brake Assist)
The primary purpose of the brake assist system is to provide auxiliary brake force to assist drivers who cannot generate a brake force large enough during emergency braking, thus helping to maximize the vehicle's braking performance.

Operation description
The skid control ECU receives speed signals from each speed sensor and the fluid pressure signal from the master cylinder pressure sensor to determine whether brake assist is necessary. If brake assist is deemed necessary, the skid control ECU sends control signals to the pump motor and solenoid. The pump and the solenoid valve then control the pressure applied to each wheel cylinder. The ABS warning light and slip indicator light come on and the VSC OFF indicator light blinks to indicate malfunctions in the BA system.
TRC (Traction Control)
The TRC system helps prevent the drive wheels from slipping if the driver presses down on the accelerator pedal excessively when starting off or accelerating on a slippery surface.

Operation description
The skid control ECU detects the vehicle's slip condition by receiving signals from each speed sensor and the ECM via CAN communication.
The skid control ECU controls engine torque with the ECM via CAN communication and brake fluid pressure through the pump and solenoid valve. The slip indicator light blinks when the system is operating. The VSC OFF indicator light blinks and the slip indicator light comes on when the TRC system malfunctions.
VSC (Vehicle Stability Control)
The VSC system helps prevent the vehicle from slipping sideways when front or rear wheel skidding occurs while cornering.

Operation description
The skid control ECU determines the vehicle condition by receiving signals from the speed sensor, yaw rate and deceleration sensor and steering angle sensor. The skid control ECU controls driving torque with the ECM via CAN communication, and brake fluid pressure with the solenoid valve.
The slip indicator light blinks and the skid control buzzer sounds when the system is operating. When there is a malfunction in the VSC system, the VSC OFF indicator light blinks and the slip indicator light comes on.
| ABS with EBD, BA, TRC and VSC OPERATION |
The skid control ECU calculates vehicle stability tendency based on the signals from the 4 wheel speed sensors, the yaw rate and deceleration sensor and the steering angle sensor. In addition, it evaluates the results of the calculations to determine whether any control actions (control of the engine output torque by electronic throttle control and of the brake fluid pressure by the VSC actuator) should be implemented.
The slip indicator light blinks and the skid control buzzer sounds to inform the driver that the VSC system is operating. The slip indicator light also blinks when traction control is operating, and the operation being performed is displayed.
| FAIL-SAFE FUNCTION |
When a failure occurs in the ABS with BA, TRC and VSC systems, the ABS warning light and slip indicator light come on and the VSC OFF indicator light blinks, and the operation of those systems is prohibited. In addition to this, when a failure which disables the EBD operation occurs, the brake warning light comes on and EBD operation is prohibited.
If control is prohibited due to a malfunction during operation, control is disabled gradually to avoid sudden vehicle instability.
| INITIAL CHECK |
When the vehicle speed first reaches approximately 23 km/h (14 mph) or more after the ignition switch has been turned ON, each solenoid valve and the VSC actuator motor are sequentially activated to perform electrical checks. During the initial check, the operating sound of the motor can be heard from the engine compartment, but this does not indicate a malfunction.
| FUNCTION OF COMPONENTS |
| Components | Functions |
| Front speed sensor (Semiconductor speed sensor, magnetic sensor rotor) |
|
| Rear speed sensor (Semiconductor speed sensor, magnetic sensor rotor) |
|
| Skid control ECU (Housed in VSC actuator) |
|
| VSC actuator |
|
| Motor relay |
|
| Solenoid relay |
|
| Steering angle sensor |
|
| Yaw rate and deceleration sensor |
|
| Master cylinder brake fluid pressure sensor |
|
| ECM |
|
| ABS warning light |
|
| Brake warning light |
|
| VSC OFF indicator light |
|
| Slip indicator light |
|
| Skid control buzzer |
|
| Stop light control relay (BRK NO. 1 and BRK NO. 2) |
|