SFI SYSTEM > TERMINALS OF ECM |
| CHECK ECM |

Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A27-1 (BATT) - D56-81 (E1) | L - BR | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| D56-41 (+BM) - D56-81 (E1) | P - BR | Power source of throttle actuator | Always | 11 to 14 V |
| A27-28 (IGSW) - D56-81 (E1) | LG - BR | Ignition switch | Ignition switch ON | 11 to 14 V |
| A27-3 (+B) - D56-81 (E1) | GR - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A27-2 (+B2) - D56-81 (E1) | GR - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| D56-58 (OC1+) - D56-57 (OC1-) | B - B-L | Camshaft oil control valve (OCV) (for Intake Side of Bank 1) | Idling | Pulse generation (see waveform 1) |
| D56-52 (OC2+) - D56-51 (OC2-) | L-B - R-B | Camshaft oil control valve (OCV) (for Intake Side of Bank 2) | Idling | Pulse generation (see waveform 1) |
| D56-56 (OE1+) - D56-55 (OE1-) | L-W - L-B | Camshaft oil control valve (OCV) (for Exhaust Side of Bank 1) | Idling | Pulse generation (see waveform 1) |
| D56-50 (OE2+) - D56-49 (OE2-) | L-R - L | Camshaft oil control valve (OCV) (for Exhaust Side of Bank 2) | Idling | Pulse generation (see waveform 1) |
| A27-34 (MREL) - D56-81 (E1) | W - BR | EFI MAIN relay | Ignition switch ON | 11 to 14 V |
| D56-74 (VG) - D56-75 (E2G) | L-Y - G-W | Mass air flow meter | Idling, Shift lever in P or N, A/C switch OFF | 0.5 to 3.0 V |
| D56-73 (THA) - D56-97 (ETHW) | Y-B - BR | Intake air temperature sensor | Idling, Intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| D56-76 (THW) - D56-98 (ETHA) | G-B - BR | Engine coolant temperature sensor | Idling, Engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| D56-80 (VCTA) - D56-79 (ETA) | Y - L | Power source of throttle position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| D56-78 (VTA1) - D56-79 (ETA) | R-Y - L | Throttle position sensor (for engine control) | Ignition switch ON, Throttle valve fully closed | 0.5 to 1.1 V |
| Ignition switch ON, Throttle valve fully open | 3.2 to 4.8 V | |||
| D56-77 (VTA2) - D56-79 (ETA) | Y-B - L | Throttle position sensor (for sensor malfunction detection) | Ignition switch ON, Throttle valve fully closed | 2.1 to 3.1 V |
| Ignition switch ON, Throttle valve fully open | 4.6 to 5.0 V | |||
| A27-55 (VPA) - A27-58 (EPA) | W - BE | Accelerator pedal position sensor (for engine control) | Ignition switch ON, Accelerator pedal released | 0.5 to 1.1 V |
| Ignition switch ON, Accelerator pedal fully depressed | 2.6 to 4.5 V | |||
| A27-56 (VPA2) - A27-60 (EPA2) | LG - BR | Accelerator pedal position sensor (for sensor malfunctioning detection) | Ignition switch ON, Accelerator pedal released | 1.2 to 2.0 V |
| Ignition switch ON, Accelerator pedal fully depressed | 3.4 to 5.3 V | |||
| A27-57 (VCPA) - A27-58 (EPA) | B - BE | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| A27-59 (VCP2) - A27-60 (EPA2) | V - BR | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
| D56-22 (HA1A) - D56-23 (E04) | L - W-B | A/F sensor heater | Idling with warm engine | Pulse generation (see waveform 2) |
| D56-22 (HA1A) - D56-23 (E04) | L - W-B | A/F sensor heater | Ignition switch ON | 11 to 14 V |
| D56-20 (HA2A) - D56-21 (E05) | G - W-B | A/F sensor heater | Idling with warm engine | Pulse generation (see waveform 2) |
| D56-20 (HA2A) - D56-21 (E05) | G - W-B | A/F sensor heater | Ignition switch ON | 11 to 14 V |
| D56-126 (A1A+) - D56-81 (E1) | G -BR | A/F sensor | Ignition switch ON | 3.3 V* |
| D56-125 (A1A-) - D56-81 (E1) | R - BR | A/F sensor | Ignition switch ON | 2.9 V* |
| D56-103 (A2A+) - D56-81 (E1) | P - BR | A/F sensor | Ignition switch ON | 3.3 V* |
| D56-102 (A2A-) - D56-81 (E1) | L - BR | A/F sensor | Ignition switch ON | 2.9 V* |
| D56-45 (HT1B) - D56-46 (E03) | G-B - W-B | Heated oxygen sensor heater | Idling | Below 3.0 V |
| D56-45 (HT1B) - D56-46 (E03) | G-B - W-B | Heated oxygen sensor heater | Ignition switch ON | 11 to 14 V |
| D56-44 (HT2B) - D56-46 (E03) | B - W-B | Heated oxygen sensor heater | Idling | Below 3.0 V |
| D56-44 (HT2B) - D56-46 (E03) | B - W-B | Heated oxygen sensor heater | Ignition switch ON | 11 to 14 V |
| D56-114 (OX1B) - D56-115 (EX1B) | G - L | Heated oxygen sensor | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor | Pulse generation (see waveform 3) |
| D56-112 (OX2B) - D56-113 (EX2B) | R - W | |||
| D56-86 (#10) - D56-43 (E01) | R-L - W-B | Injector | Ignition switch ON | 11 to 14 V |
| D56-109 (#20) - D56-43 (E01) | L - W-B | Idling | Pulse generation (see waveform 4) | |
| D56-85 (#30) - D56-43 (E01) | R - W-B | |||
| D56-108 (#40) - D56-43 (E01) | Y - W-B | |||
| D56-84 (#50) - D56-43 (E01) | G - W-B | |||
| D56-107 (#60) - D56-43 (E01) | R - W-B | |||
| D56-83 (#70) - D56-43 (E01) | W - W-B | |||
| D56-106 (#80) - D56-43 (E01) | R-B - W-B | |||
| D56-94 (KNK1) - D56-93 (EKNK) | R - G | Knock sensor | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation (see waveform 5) |
| D56-117 (KNK2) - D56-116 (EKN2) | W - B | |||
| D56-96 (KNK3) - D56-95 (EKN3) | W - B | |||
| D56-119 (KNK4) - D56-118 (EKN4) | R - G | |||
| D56-92 (VV1+) - D56-91 (VV1-) | R - G | Variable valve timing (VVT) sensor (for Intake Side of Bank 1) | Idling | Pulse generation (see waveform 6) |
| D56-87 (VV2+) - D56-88 (VV2-) | R - Y | Variable valve timing (VVT) sensor (for Intake Side for Bank 2) | Idling | Pulse generation (see waveform 6) |
| D56-69 (EV1+) - D56-68 (EV1-) | R-L - B | Variable valve timing (VVT) sensor (for Exhaust Side of Bank 1) | Idling | Pulse generation (see waveform 17) |
| D56-64 (EV2+) - D56-65 (EV2-) | R-L - B | Variable valve timing (VVT) sensor (for Exhaust Side of Bank 2) | Idling | Pulse generation (see waveform 17) |
| D56-110 (NE+) - D56-111 (NE-) | W - Y | Crankshaft position sensor | Idling | Pulse generation (see waveform 6) |
| D56-40 (IGT1) - D56-81 (E1) | B-Y - BR | Ignition coil (ignition signal) | Idling | Pulse generation (see waveform 7) |
| D56-33 (IGT2) - D56-81 (E1) | L-Y - BR | |||
| D56-37 (IGT3) - D56-81 (E1) | B - BR | |||
| D56-34 (IGT4) - D56-81 (E1) | L-B - BR | |||
| D56-35 (IGT5) - D56-81 (E1) | G-R - BR | |||
| D56-36 (IGT6) - D56-81 (E1) | G - BR | |||
| D56-38 (IGT7) - D56-81 (E1) | G-W - BR | |||
| D56-39 (IGT8) - D56-81 (E1) | G-B - BR | |||
| D56-104 (IGF1) - D56-81 (E1) | G-B - BR | Ignition coil (ignition confirmation signal) | Ignition switch ON | 4.5 to 5.5 V |
| Idling | Pulse generation (see waveform 7) | |||
| D56-105 (IGF2) - D56-81 (E1) | R - BR | Ignition coil (ignition confirmation signal) | Ignition switch ON | 4.5 to 5.5 V |
| Idling | Pulse generation (see waveform 7) | |||
| D56-63 (PRG) - D56-81 (E1) | L-B - BR | Purge VSV | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation (see waveform 8) | |||
| A27-13 (SPD) - D56-81 (E1) | B - BR | Speed signal from combination meter | Driving at 20 km/h (12 mph) | Pulse generation (see waveform 9) |
| A27-46 (STA) - D56-81 (E1) | R - BR | Starter signal | Cranking | 5.5 V or more |
| D56-120 (NSW) - D56-81 (E1) | L - BR | Park/neutral position switch | Ignition switch ON, Shift lever position other than P or N | 11 to 14 V |
| Ignition switch ON, Shift lever in P or N | Below 3.0 V | |||
| A27-26 (STP) - D56-81 (E1) | LG - BR | Stop light switch | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V | |||
| A27-35 (ST1-) - D56-81 (E1) | R - BR | Stop light switch (opposite to STP terminal) | Ignition switch ON, Brake pedal depressed | Below 1.5 V |
| Ignition switch ON, Brake pedal released | 7.5 to 14 V | |||
| D56-19 (M+) - D56-82 (ME01) | R - W-B | Throttle actuator | Idling with warm engine | Pulse generation (see waveform 10) |
| D56-18 (M-) - D56-82 (ME01) | G - W-B | Throttle actuator | Idling with warm engine | Pulse generation (see waveform 11) |
| A27-48 (FC) - D56-81 (E1) | L - BR | Fuel pump control | Ignition switch ON | 11 to 14 V |
| A27-52 (FPC) - D56-81 (E1) | BE - BR | Fuel pump control | Ignition switch ON | Below 1.5 V |
| A27-24 (W) - D56-81 (E1) | P - BR | MIL | Ignition switch ON | Below 3.0 V |
| Idling | 11 to 14 V | |||
| A27-16 (TC) - D56-81 (E1) | R - BR | Terminal TC of DLC3 | Ignition switch ON | 11 to 14 V |
| A27-15 (TACH) - D56-81 (E1) | W - BR | Engine speed | Idling | Pulse generation (see waveform 12) |
| D56-67 (VCV1) - D56-97 (ETHW) | L - BR | Power source for sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| D56-66 (VCV2) - D56-97 (ETHW) | L - BR | Power source for sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| D56-32 (ALT) - D56-81 (E1) | R - BR | Generator | Ignition switch ON | 11 to 14 V |
| A27-10 (CANH) - D56-81 (E1) | GR - BR | CAN communication line | Ignition switch ON | Pulse generation (see waveform 13) |
| A27-11 (CANL) - D56-81 (E1) | W - BR | CAN communication line | Ignition switch ON | Pulse generation (see waveform 14) |
| D56-62 (ACIS) - D56-81 (E1) | L-Y - BR | VSV for ACIS (Acoustic Control Induction System) operation signal | Ignition switch ON | 11 to 14 V |
| D56-28 (AIRV) - D56-81 (E1) | BR - BR | Air switching valve for secondary air injection system | Ignition switch ON | 11 to 14 V |
| D56-54 (AIRP) - D56-81 (E1) | P - BR | Air pump control | Ignition switch ON | 11 to 14 V |
| D56-30 (AIDI) - D56-81 (E1) | G - BR | Diagnostic information signal for air injection system | Air injection system operates | Pulse generation (see waveform 16) |
| A27-54 (AIP) - D56-98 (ETHA) | Y - BR | Secondary air injection system pressure signal | Ignition switch ON | 3.0 to 3.6 V |
| A27-43 (ARV2) - D56-81 (E1) | V - BR | Air switching valve for secondary air injection system | Ignition switch ON | 11 to 14 V |
| D56-53 (ARP2) - D56-81 (E1) | P-L - BR | Air pump control | Ignition switch ON | 11 to 14 V |
| D56-29 (AID2) - D56-81 (E1) | G-Y - BR | Diagnostic information signal for air injection system | Air injection system operates | Pulse generation (see waveform 16) |
| A27-53 (AIP2) - D56-97 (ETHW) | G - BR | Secondary air injection system pressure signal | Ignition switch ON | 3.0 to 3.6 V |
| D56-90 (G2) - D56-89 (G2-) | R - B | Camshaft position sensor | Idling | Pulse generation (see waveform 15) |
| A27-18 (DI) - D56-81 (E1) | Y - BR | Fuel pump control | Ignition switch ON | 0 to 3.0 V |
| A27-14 (STSW) - D56-81 (E1) | BR - BR | Starter switch | Shift lever in P or N, Cranking | 6.0 V or more |
| A27-41 (ACCR) - D56-81 (E1) | BR - BR | ACC relay control signal | Ignition switch ON → Cranking | 11 to 14 V → Below 1 V |
| D56-16 (STAR) - D56-81 (E1) | L - BR | Starter relay control | Ignition switch ON | Below 1.5 V |
| Cranking | 5.5 V or more | |||
| D56-72 (PSP) - D56-81 (E1) | G - BR | Power steering oil pressure sensor | Ignition switch ON | 0.5 to 4.5 V |
![]() |
WAVEFORM 1:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D56-58 (OC1+) - D56-57 (OC1-) | 5 V/DIV., 1 msec./DIV. | Idling |
| D56-52 (OC2+) - D56-51 (OC2-) | 5 V/DIV., 1 msec./DIV. | Idling |
| D56-56 (OE1+) - D56-55 (OE1-) | 5 V/DIV., 1 msec./DIV. | Idling |
| D56-50 (OE2+) - D56-49 (OE2-) | 5 V/DIV., 1 msec./DIV. | Idling |
![]() |
WAVEFORM 2:
| Terminal No. (Symbol) | Tool Setting | Condition |
| CH1: D56-22 (HA1A) - D56-23 (E04) | 5 V/DIV., 10 msec./DIV. | Idle with warm engine |
| CH2: D56-20 (HA2A) - D56-21 (E05) | 5 V/DIV., 10 msec./DIV. | Idle with warm engine |
![]() |
WAVEFORM 3:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D56-114 (OX1B) - D56-115 (EX1B) | 0.2 V/DIV., 200 msec./DIV. | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
| D56-112 (OX2B) - D56-113 (EX2B) | 0.2 V/DIV., 200 msec./DIV. | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
![]() |
WAVEFORM 4:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D56-86 (#10) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-109 (#20) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-85 (#30) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-108 (#40) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-84 (#50) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-107 (#60) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-83 (#70) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-106 (#80) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
![]() |
WAVEFORM 5:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D56-94 (KNK1) - D56-93 (EKNK) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
| D56-117 (KNK2) - D56-116 (EKN2) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
| D56-96 (KNK3) - D56-95 (EKN3) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
| D56-119 (KNK4) - D56-118 (EKN4) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
![]() |
WAVEFORM 6:
| Terminal No. (Symbol) | Tool Setting | Condition |
| (a) D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
| (b) D56-92 (VV1+) - D56-91 (VV1-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
| (c) D56-87 (VV2+) - D56-88 (VV2-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
![]() |
WAVEFORM 7:
| Terminal No. (Symbol) | Tool Setting | Condition |
| (a) D56-40 (IGT1) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-33 (IGT2) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-37 (IGT3) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-34 (IGT4) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-35 (IGT5) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-36 (IGT6) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-38 (IGT7) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-39 (IGT8) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (b) D56-104 (IGF1) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (b) D56-105 (IGF2) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
![]() |
WAVEFORM 8:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D56-63 (PRG) - D56-81 (E1) | 10 V/DIV., 10 to 100 msec./DIV. | Idling |
![]() |
WAVEFORM 9:
| Terminal No. (Symbol) | Tool Setting | Condition |
| A27-13 (SPD) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Driving at 20 km/h (12 mph) |
![]() |
WAVEFORM 10:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D56-19 (M+) - D56-82 (ME01) | 5 V/DIV., 1 msec./DIV. | Idling with warm engine |
![]() |
WAVEFORM 11:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D56-18 (M-) - D56-82 (ME01) | 5 V/DIV., 1 msec./DIV. | Idling with warm engine |
![]() |
WAVEFORM 12:
| Terminal No. (Symbol) | Tool Setting | Condition |
| A27-15 (TACH) - D56-81 (E1) | 5 V/DIV., 10 msec./DIV. | Idling |
![]() |
WAVEFORM 13:
| Terminal No. (Symbol) | Tool Setting | Condition |
| A27-10 (CANH) - D56-81 (E1) | 1 V/DIV., 10 μsec./DIV. | Engine stops and ignition switch ON |
![]() |
WAVEFORM 14:
| Terminal No. (Symbol) | Tool Setting | Condition |
| A27-11 (CANL) - D56-81 (E1) | 1 V/DIV., 10 μsec./DIV. | Engine stops and ignition switch ON |
![]() |
WAVEFORM 15:
| Terminal No. (Symbol) | Tool Setting | Condition |
| CH1: D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
| CH2: D56-90 (G2) - D56-89 (G2-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
![]() |
WAVEFORM 16:
| Terminal No. (Symbol) | Tool Setting | Condition |
| D56-30 (AIDI) - D56-81 (E1) | 5 V/DIV., 20 to 40 msec./DIV. | Performing system check using intelligent tester (air injection check) |
| D56-29 (AID2) - D56-81 (E1) | 5 V/DIV., 20 to 40 msec./DIV. | Performing system check using intelligent tester (air injection check) |
![]() |
WAVEFORM 17:
| Terminal No. (Symbol) | Tool Setting | Condition |
| (a) D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
| (b) D56-69 (EV1+) - D56-68 (EV1-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
| (c) D56-64 (EV2+) - D56-65 (EV2-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |