SFI SYSTEM > FREEZE FRAME DATA |
| DESCRIPTION |
![]() |
| LIST OF FREEZE FRAME DATA |
| Tester Display | Measurement Item | Diagnostic Note |
| Vehicle Speed | Vehicle speed | Speed indicated on speedometer. |
| Engine Speed | Engine speed | - |
| Calculate Load | Calculated load | Calculated load by ECM. |
| Vehicle Load | Vehicle load | - |
| MAF | Mass air flow volume | If approximately 0.0 g/sec.:
|
| Atmosphere Pressure | Atmosphere pressure | - |
| Coolant Temp | Engine coolant temperature | If -40°C (-40°F), sensor circuit open. If 140°C (284°F) or more, sensor circuit shorted. |
| Intake Air | Intake air temperature | If -40°C (-40°F), sensor circuit open. If 140°C (284°F) or more, sensor circuit shorted. |
| Engine Run Time | Accumulated engine running time | - |
| Initial Engine Coolant Temp | Engine coolant temperature at engine start | - |
| Initial Intake Air Temp | Intake air temperature at engine start | - |
| Battery Voltage | Battery voltage | - |
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position (APP) No. 1 | - |
| Accel Sens. No.2 Volt % | Absolute APP No. 2 | - |
| Throttle Sensor Volt % | Throttle sensor positioning | - |
| Throttl Sensor #2 Volt % | Throttle sensor positioning #2 | - |
| Throttle Sensor Position | Throttle position | - |
| Throttle Motor DUTY | Throttle motor | - |
| Injector (Port) | Injection period of No. 1 cylinder | - |
| Injection Volum (Cylinder 1) | Injection volume | - |
| Fuel Pump/Speed Status | Fuel pump/speed status | - |
| EVAP (Purge) VSV | EVAP purge VSV duty ratio | - |
| Evap Purge Flow | Ratio of evaporative purge flow to intake air volume | - |
| Purge Density Learn Value | Learning value of purge density | - |
| EVAP Purge VSV | EVAP Purge VSV | - |
| Target Air-Fuel Ratio | Ratio compared to stoichiometric level | - |
| AF Lambda B1S1 | Fuel trim at A/F sensor | - |
| AF Lambda B2S1 | Fuel trim at A/F sensor | - |
| AFS Voltage B1S1 AFS Voltage B2S1 | A/F sensor output | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor. |
| AFS Current B1S1 | A/F sensor current | - |
| AFS Current B2S1 | A/F sensor current | - |
| O2S B1S2 O2S B2S2 | Heated oxygen sensor output | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor. |
| O2S Impedance B1S2 O2S Impedance B2S2 | Sub heated oxygen sensor impedance (for Sensor 2) | - |
| Short FT #1 | Short-term fuel trim | Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio. |
| Long FT #1 | Long-term fuel trim | Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value. |
| Short FT #2 | Short-term fuel trim | Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio. |
| Long FT #2 | Long-term fuel trim | Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value. |
| Fuel System Status #1 | Fuel system status (for Bank 1) |
|
| Fuel System Status #2 | Fuel system status (for Bank 2) |
|
| Air pump pressure (absolute) | Air pump pressure | - |
| Air Pump2 Pressure (Absolute) | Air pump pressure | - |
| Air Pump Pulsation Pressure | Air pump pulsation pressure | - |
| Air Pump2 Pulsation Pressure | Air pump pulsation pressure | - |
| Secondary Air Control VSV | Secondary air injection system status | - |
| 2nd Air System Status | Second air system status | - |
| AI Test | Secondary air injection system operation prohibit | - |
| IGN Advance | Ignition advance | - |
| Knock Feedback Value | Feedback value of knocking | - |
| Knock Correct Learn Value | Correction learning value of knocking | - |
| ACIS VSV | VSV for Acoustic Control Induction System (ACIS) | - |
| VVT Control Status #1 | VVT control status | - |
| VVT Control Status #2 | VVT control status | - |
| Catalyst Temp B1S1 | Estimated catalyst temperature (for Sensor 1) | - |
| Catalyst Temp B2S1 | Estimated catalyst temperature (for Sensor 1) | - |
| Catalyst Temp B1S2 | Estimated catalyst temperature (for Sensor 2) | - |
| Catalyst Temp B2S2 | Estimated catalyst temperature (for Sensor 2) | - |
| Starter Signal | Starter switch (STSW) signal | - |
| Starter Control | Starter switch status | - |
| Power Steering Signal Record | Power steering switch status | - |
| Starter Relay | Starter relay status | - |
| Power Steer. Sig. Record | Power steering signal (history) | This signal status is usually ON until the cables are disconnected from the battery terminals. |
| ACC Relay | ACC relay status | - |
| Neutral Position SW Signal | Park/Neutral position (PNP) switch signal | - |
| Stop Light Switch | Stop light switch | - |
| A/C Signal | A/C signal | - |
| Closed Throttle Position SW | Closed throttle position switch | - |
| Fuel Cut Condition | Fuel cut condition | - |
| Immobiliser Communication | Immobiliser communication | - |
| Electrical Load Signal | Electrical load signal | - |
| Time after DTC Cleared | Cumulative time after DTC cleared | - |
| Distance from DTC Cleared | Accumulated distance from DTC cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared | - |
| TC and TE1 | TC and CG (TE1) terminals of DLC3 | - |
| Ignition Trig. Count | Ignition counter | - |
| Cylinder #1 Misfire Count | Cylinder #1 misfire | - |
| Cylinder #2 Misfire Count | Cylinder #2 misfire | - |
| Cylinder #3 Misfire Count | Cylinder #3 misfire | - |
| Cylinder #4 Misfire Count | Cylinder #4 misfire | - |
| Cylinder #5 Misfire Count | Cylinder #5 misfire | - |
| Cylinder #6 Misfire Count | Cylinder #6 misfire | - |
| Cylinder #7 Misfire Count | Cylinder #7 misfire | - |
| Cylinder #8 Misfire Count | Cylinder #8 misfire | - |
| All Cylinders Misfire Count | All cylinders misfire | - |
| Multi Cylinders Misfire Count | Multiple cylinder misfire | - |
| Misfire RPM | Engine speed when misfire occurred | - |
| Misfire Load | Engine load when misfire occurred | - |
| Misfire Margin | Margin to detect engine misfire | - |
| Catalyst OT MF F/C | Catalyst over temperature misfire prevention F/C | - |
| Cat OT MF F/C History | Catalyst over temperature misfire prevention F/C history | - |
| Cat OT MF F/C Cylinder#1 | Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#2 | Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#3 | Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#4 | Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#5 | Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#6 | Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#7 | Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#8 | Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected) | - |
| Power Steering Pressure | Power steering pressure sensor | - |
| ACT VSV | A/C cut status for Active Test | - |
| Idle Fuel Cut | Fuel cut idle | ON: when throttle valve fully closed and engine speed over 3500 rpm. |
| FC TAU | Fuel cut during very light load | Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete. |
| SPD (NT) | Input shaft speed | Data is displayed in increments of 50 rpm. |
| SPD (SP2) | Output shaft speed | - |