Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > FREEZE FRAME DATA

for Preparation Click here



DESCRIPTION
  1. Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was moving or stationary, the engine was warmed up or not, the air-fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.


  1. A103809E27
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data can be checked.
    1. 3 data sets before the DTC was set.
    2. 1 data set when the DTC was set.
    3. 1 data set after the DTC was set.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA

Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on speedometer.
Engine Speed
Engine speed
-
Calculate Load
Calculated load
Calculated load by ECM.
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If approximately 0.0 gm/s:
  1. Mass air flow meter power source circuit open or short.
  1. VG circuit open or short.
If 160.0 gm/s or more:
  1. E2G circuit open.
Atmosphere Pressure
Atmosphere pressure
-
Coolant Temp
Engine coolant temperature
If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
Intake Air
Intake air temperature
If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Battery Voltage
Battery voltage
-
Accel Sens. No.1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1
-
Accel Sens. No.2 Volt %
Absolute APP No. 2
-
Throttle Sensor Volt %
Throttle sensor positioning
-
Throttl Sensor #2 Volt %
Throttle sensor positioning #2
-
Throttle Sensor Position
Throttle position
-
Throttle Motor DUTY
Throttle actuator
-
Throttle Position
Throttle Position
For use when engine stall, starting problems or rough idle is present.
ISC Flow
Flow rate calculated using information from each sensor
For use when engine stall, starting problems or rough idle is present.
ISC Position
Requested opening amount calculated using ISC control
For use when engine stall, starting problems or rough idle is present.
ISC Feedback Value
ISC feedback compensation amount
For use when engine stall, starting problems or rough idle is present.
ISC Learning Value
ISC learned compensation amount
For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val
Compensation flow rate according to electrical load
For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val
Compensation flow rate according to air conditioner load
For use when engine stall, starting problems or rough idle is present.
PS Feedback Val
Compensation flow rate according to power steering load
For use when engine stall, starting problems or rough idle is present.
Low Revolution Control
Low engine speed control operation state
For use when engine stall, starting problems or rough idle is present.
Neutral Control
Neutral control operation state
For use when engine stall, starting problems or rough idle is present.
N Range Status
Shift lever N status
For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow
Intake air compensation flow rate
For use when engine stall, starting problems or rough idle is present.
Deposit Loss Flow
Flow loss due to deposits
For use when engine stall, starting problems or rough idle is present.
Fuel Pump Duty
Fuel pump duty
-
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder 1)
Injection volume
-
Current Fuel Type
Status of the current fuel type
-
EVAP (Purge) VSV
Purge VSV duty ratio
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learning value of purge density
-
EVAP Purge VSV
Purge VSV
-
Purge Cut VSV Duty
Purge cut VSV duty
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1S1
Fuel trim at A/F sensor
-
AF Lambda B2S1
Fuel trim at A/F sensor
-
AFS Voltage B1S1
A/F sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
AFS Voltage B2S1
A/F sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
AFS Current B1S1
A/F sensor current
-
AFS Current B2S1
A/F sensor current
-
A/F Heater Duty #1
A/F heater duty ratio (for Bank 1)
-
A/F Heater Duty #2
A/F heater duty ratio (for Bank 2)
-
O2S B1S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
O2S B2S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
O2S Impedance B1S2
Sub heated oxygen sensor impedance (for Sensor 2)
-
O2S Impedance B2S2
Sub heated oxygen sensor impedance (for Sensor 2)
-
O2 Heater B1S2
Heated oxygen sensor heater
-
O2 Heater B2S2
Heated oxygen sensor heater
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
Long FT #1
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value.
A/F Learn Value Idle #1
Air fuel ratio learn value area of idle (for Bank 1)
-
A/F Learn Value Low #1
Air fuel ratio learn value area of low load (for Bank 1)
-
A/F Learn Value Mid1 #1
Air fuel ratio learn value area of middle load 1 (for Bank 1)
-
A/F Learn Value Mid2 #1
Air fuel ratio learn value area of middle load 2 (for Bank 1)
-
A/F Learn Value High #1
Air fuel ratio learn value area of high load (for Bank 1)
-
Total FT #1
Total fuel trim
-
Short FT #2
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
Long FT #2
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value.
A/F Learn Value Idle #2
Air fuel ratio learn value area of idle (for Bank 2)
-
A/F Learn Value Low #2
Air fuel ratio learn value area of low load (for Bank 2)
-
A/F Learn Value Mid1 #2
Air fuel ratio learn value area of middle load 1 (for Bank 2)
-
A/F Learn Value Mid2 #2
Air fuel ratio learn value area of middle load 2 (for Bank 2)
-
A/F Learn Value High #2
Air fuel ratio learn value area of high load (for Bank 2)
-
Total FT #2
Total fuel trim
-
Fuel System Status #1
Fuel system status (for Bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop.
  2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to detected system fault.
  5. CLFault: Closed loop but heated oxygen sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (for Bank 2)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop.
  2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to detected system fault.
  5. CLFault: Closed loop but heated oxygen sensor, which is used for fuel control, is malfunctioning.
IGN Advance
Ignition advance
-
IGN Advance
IGN Advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
Idle Spark Advn Ctrl #1
Individual cylinder timing advance compensation amount (No. 1)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2
Individual cylinder timing advance compensation amount (No. 2)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3
Individual cylinder timing advance compensation amount (No. 3)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 4)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #5
Individual cylinder timing advance compensation amount (No. 5)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #6
Individual cylinder timing advance compensation amount (No. 6)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #7
Individual cylinder timing advance compensation amount (No. 7)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #8
Individual cylinder timing advance compensation amount (No. 8)
For use when engine stall, starting problems or rough idle is present.
ACIS VSV
VSV for Acoustic Control Induction System (ACIS)
-
Actual VVT Angle #1
Actual VVT angle (for Bank 1)
-
Actual VVT Angle #2
Actual VVT angle (for Bank 2)
-
Actual VVT Ex Angle #1
Actual exhaust VVT angle (for Bank 1)
-
Actual VVT Ex Angle #2
Actual exhaust VVT angle (for Bank 2)
-
VVT Control Status #1
VVT control status
-
VVT Control Status #2
VVT control status
-
Catalyst Temp B1S1
Estimated catalyst temperature (for Sensor 1)
-
Catalyst Temp B2S1
Estimated catalyst temperature (for Sensor 1)
-
Catalyst Temp B1S2
Estimated catalyst temperature (for Sensor 2)
-
Catalyst Temp B2S2
Estimated catalyst temperature (for Sensor 2)
-
Starter Signal
Starter switch (STSW) signal
-
Starter Control
Starter switch status
-
Power Steering Signal
Power steering switch status
-
Starter Relay
Starter relay status
-
ACC Relay
ACC relay status
-
Neutral Position SW Signal
Park/Neutral position (PNP) switch signal
-
Transfer L4
L4 status of the transfer
-
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
-
Immobiliser Communication
Immobiliser communication
-
TC Terminal
TC terminal status
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
Dist Batt Cable Disconnect
Accumulated distance from battery cable disconnected
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Ignition Trig. Count
Ignition counter
-
Cylinder #1 Misfire Count
Misfire Count of Cylinder #1
-
Cylinder #2 Misfire Count
Misfire Count of Cylinder #2
-
Cylinder #3 Misfire Count
Misfire Count of Cylinder #3
-
Cylinder #4 Misfire Count
Misfire Count of Cylinder #4
-
Cylinder #5 Misfire Count
Misfire Count of Cylinder #5
-
Cylinder #6 Misfire Count
Misfire Count of Cylinder #6
-
Cylinder #7 Misfire Count
Misfire Count of Cylinder #7
-
Cylinder #8 Misfire Count
Misfire Count of Cylinder #8
-
All Cylinders Misfire Count
All cylinders misfire count
-
Multi Cylinders Misfire Count
Multiple cylinder misfire count
-
Misfire RPM
Engine speed when misfire occurred
-
Misfire Load
Engine load when misfire occurred
-
Misfire Margin
Misfire monitoring
-
Catalyst OT MF F/C
Catalyst over temperature misfire prevention F/C
-
Cat OT MF F/C History
Catalyst over temperature misfire prevention F/C history
-
Cat OT MF F/C Cylinder#1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#5
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#6
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#7
Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#8
Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)
-
Engine Speed (Starter Off)
Engine speed when starter off
For use when engine stall, starting problems or rough idle is present.
Starter Count
Number of times starter turned on after ignition switch turned to ON
For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip
Distance driven during previous trip
Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

HINT:
Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.

Engine Starting Time
Time elapsed after engine started (interval between ignition switch ON and off)
For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp
Engine coolant temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp
Intake air temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature
Engine oil temperature (estimated temperature)
For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C
Ambient temperature for A/C
For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp
Ambient temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation
History of hesitation during engine start
For use when engine stall, starting problems or rough idle is present.
Low Rev for Eng Start
History of low engine speed after engine start
For use when engine stall, starting problems or rough idle is present.
Minimum Engine Speed
Minimum engine speed
For use when engine stall, starting problems or rough idle is present.
Power Steering Pressure
Power steering pressure sensor
-
ACT VSV
A/C cut status for Active Test
-
Brake Override System
Brake Override System
-
Idle Fuel Cut
Fuel cut idle
ON: when throttle valve fully closed and engine speed over 3500 rpm.
FC TAU
Fuel cut during very light load
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete.
Immobiliser Fuel Cut
Status of the immobiliser fuel cut
-
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut history
-
Vehicle Spec Signal 1
Status of the Vehicle Spec Judge Signal 1
-
Electrical Load Signal 1
Electrical load signal
-
Electrical Load Signal 2
Electrical load signal
-
Cruise Cancel Signal
Status of the cruise cancel signal
-
SPD (NT)
Input shaft speed
Data is displayed in increments of 50 rpm.
SPD (SP2)
Output shaft speed
-