Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0010    Camshaft Position "A" Actuator Circuit (Bank 1)

DTC    P0020    Camshaft Position "A" Actuator Circuit (Bank 2)

for Preparation Click here


DESCRIPTION

  1. This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
  2. The VVT (variable valve timing) system adjusts the intake valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A192077E01


DTC No.
DTC Detection Condition
Trouble Area
P0010
Open or short in OCV for intake camshaft (for Bank 1) circuit
(1 trip detection logic)
  1. Open or short in OCV for intake camshaft (for Bank 1) circuit
  2. OCV for intake camshaft (for Bank 1)
  3. ECM
P0020
Open or short in OCV for intake camshaft (for Bank 2) circuit
(1 trip detection logic)
  1. Open or short in OCV for intake camshaft (for Bank 2) circuit
  2. OCV for intake camshaft (for Bank 2)
  3. ECM

HINT:
This DTC relates to the Oil Control Valve (OCV).


MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM


A178641E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK DTC
  1. Clear DTC after recording the freeze frame data and DTC (Click here).

  1. Turn the ignition switch off.

  1. Allow the engine to idle and check DTC.

  1. Check that P0010 or P0020 is not present.

    OK:
    P0010 or P0020 is not present.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CAMSHAFT OIL CONTROL VALVE


    A160397E02
  1. Disconnect the OCV connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω



NG
REPLACE CAMSHAFT OIL CONTROL VALVE (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (OCV - ECM)
  1. Disconnect the OCV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D26-1 - D56-58 (OC1+)
    Always
    Below 1 Ω
    D27-1 - D56-52 (OC2+)
    Always
    Below 1 Ω
    D26-2 - D56-57 (OC1-)
    Always
    Below 1 Ω
    D27-2 - D56-51 (OC2-)
    Always
    Below 1 Ω
    D26-1 or D56-58 (OC1+) - Body ground
    Always
    10 kΩ or higher
    D27-1 or D56-52 (OC2+) - Body ground
    Always
    10 kΩ or higher
    D26-2 or D56-57 (OC1-) - Body ground
    Always
    10 kΩ or higher
    D27-2 or D56-51 (OC2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)