Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0115    Engine Coolant Temperature Circuit Malfunction

DTC    P0117    Engine Coolant Temperature Circuit Low Input

DTC    P0118    Engine Coolant Temperature Circuit High Input

for Preparation Click here


DESCRIPTION

A thermistor, whose resistance value varies according to the ECT, is built into the Engine Coolant Temperature (ECT) sensor.
The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature (IAT) sensor.

HINT:
When any of DTCs P0115, P0117 and P0118 are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECT is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No.
DTC Detection Condition
Trouble Area
P0115
Open or short in ECT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in ECT sensor circuit
  2. ECT sensor
  3. ECM
P0117
Short in ECT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Short in ECT sensor
  2. ECT sensor
  3. ECM
P0118
Open in ECT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open in ECT sensor circuit
  2. ECT sensor
  3. ECM

HINT:
When any of these DTCs are stored, check the ECT by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.


Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit

MONITOR DESCRIPTION

The Engine Coolant Temperature (ECT) sensor is used to monitor the ECT. The ECT sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the ECT. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the ECT sensor and stores a DTC.
Example:
If the sensor output voltage is more than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the ECT sensor circuit, and stores DTC P0118. Conversely, if the voltage output is less than 0.14 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0117.
If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

WIRING DIAGRAM


A178643E03


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ OUTPUT DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0115 is output
    A
    P0117 is output
    B
    P0118 is output
    C



B
Go to step 5

C
Go to step 3
A


2.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the value displayed on the intelligent tester.

    Standard value:
    Between 80 and 100°C (167 and 212°F) with warm engine.

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    Between 80 and 100°C (176 and 212°F)
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    1. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
A107691E68
  1. Disconnect the ECT sensor connector.

  1. Connect terminals 1 and 2 of the ECT sensor connector on the wire harness side.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the value displayed on the intelligent tester.

    Standard value:
    140°C (284°F) or higher



NG
Go to step 4
OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
A160266E12
  1. Disconnect the ECT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D15-2 - D56-76 (THW)
    Always
    Below 1 Ω
    D15-1 - D56-98 (ETHA)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GOOD CONNECTION TO ECM. IF OK, REPLACE ECM (Click here)  

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
A164746E09
  1. Disconnect the ECT sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the value displayed on the intelligent tester.

    Standard value:
    -40°C (-40°F)



NG
Go to step 6
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

6.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
A160266E11
  1. Disconnect the ECT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D15-2 or D56-76 (THW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)