Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0037    Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

DTC    P0038    Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)

DTC    P0057    Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)

DTC    P0058    Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)

DTC    P102D    O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON

DTC    P105D    O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON

for Preparation Click here


DESCRIPTION

  1. Refer to DTC P0137 .

HINT:
  1. When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the Heated Oxygen (HO2) Sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

  2. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The HO2 sensor heater circuit uses a relay on the +B side of the circuit.


    A164717E06


DTC No.
DTC Detection Condition
Trouble Area
P0037
P0057
The heater current is less than the specified value while the heater is operating.
(1 trip detection logic)
  1. Open in HO2 sensor heater circuit
  2. HO2 sensor heater (for Sensor 2)
  3. Integration relay
  4. ECM
P0038
P0058
The heater current is higher than the specified value while the heater is operating.
(1 trip detection logic)
  1. Short in HO2 sensor heater circuit
  2. HO2 sensor heater (for Sensor 2)
  3. Integration relay
  4. ECM
P102D
P105D
The heater current is higher than the specified value while the heater is not operating.
(1 trip detection logic)
ECM

MONITOR DESCRIPTION

The sensing portion of the Heated Oxygen (HO2) sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.
  1. Heated oxygen sensor heater range check (P0037, P0038, P0057 and P0058):
    The ECM monitors the current applied to the O2 sensor heater to check the heater for malfunctions. If the current is below the threshold value, the ECM determines that there is an open circuit in the heater. If the current is above the threshold value, the ECM determines that there is a short circuit in the heater.
    The ECM constantly monitors the current applied to the heater. If the ECM detects an open or short circuit, the ECM turns the MIL on and stores a DTC.
    If a malfunction is detected, the ECM cuts off the current applied to the heater.

WIRING DIAGRAM

Refer to DTC P0137 .

CONFIRMATION DRIVING PATTERN


A198819E63

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / DTC [E].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.


INSPECTION PROCEDURE

HINT:
  1. Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Bank 1 refers to the bank that includes No. 1 cylinder.
  4. Bank 2 refers to the bank that does not include No. 1 cylinder.
  5. Sensor 1 refers to the sensor closest to the engine assembly.
  6. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
  1. Inspect the heated oxygen sensor (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)
A149595E15
  1. Disconnect the HO2 sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D17-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    D18-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 5
A


3.INSPECT INTEGRATION RELAY (EFI MAIN)
A148742E04
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI NO. 1 fuse.

    1. Remove the EFI NO. 1 fuse from the integration relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      EFI NO. 1 fuse
      Always
      Below 1 Ω

    3. Reinstall the EFI NO. 1 fuse.

  1. Inspect the EFI MAIN relay.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1C-1 - 1B-4
      When no battery voltage applied to terminals 1B-2 and 1B-3
      10 kΩ or higher
      When battery voltage applied to terminals 1B-2 and 1B-3
      Below 1 Ω



NG
REPLACE INTEGRATION RELAY (EFI MAIN)
OK


4.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - INTEGRATION RELAY)
  1. Check the EFI NO. 2 fuse.

    1. Remove the EFI NO. 2 fuse from the engine room relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      EFI NO. 2 fuse
      Always
      Below 1 Ω

    3. Reinstall the EFI NO. 2 fuse.

  1. Disconnect the HO2 sensor connector.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D17-2 (+B) - 1B-4
    Always
    Below 1 Ω
    D18-2 (+B) - 1B-4
    Always
    Below 1 Ω
    D17-2 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    D18-2 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

5.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)
  1. Disconnect the HO2 sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D17-1 (HT1B) - D56-45 (HT1B)
    Always
    Below 1 Ω
    D18-1 (HT2B) - D56-44 (HT2B)
    Always
    Below 1 Ω
    D17-1 (HT1B) or D56-45 (HT1B) - Body ground
    Always
    10 kΩ or higher
    D18-1 (HT2B) or D56-44 (HT2B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0037, P0038, P0057, P0058, P102D and/or P105D are output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)