DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2120 | VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2122 | VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic) |
|
| P2123 | VPA 4.8 V or more for 2.0 seconds or more (1 trip detection logic) |
|
| P2125 | VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2127 | VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released (1 trip detection logic) |
|
| P2128 | Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 4.8 V or more (b) VPA between 0.4 V and 3.45 V |
|
| P2138 | Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 0.02 V or less (b) VPA 0.4 V or less and VPA2 1.2 V or less |
|
| Trouble Area | Accel Sensor Out No. 1 When AP Released | Accel Sensor Out No. 2 When AP Released | Accel Sensor Out No. 1 When AP Depressed | Accel Sensor Out No. 2 When AP Depressed |
| VCP circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 4.7 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| EPA circuit open | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 4.7 V |

| 1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION SENSOR) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the value displayed on the intelligent tester.
| Accelerator Pedal Operation | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 |
| Released → Depressed → Released | 0.5 to 4.5 V | 1.2 to 4.7 V |
| Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2 is greater than 0.02 V | Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2 is greater than 0.02 V |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the APP sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A17-6 (VPA) - A27-55 (VPA) | Always | Below 1 Ω |
| A17-5 (EPA) - A27-58 (EPA) | Always | Below 1 Ω |
| A17-4 (VCPA) - A27-57 (VCPA) | Always | Below 1 Ω |
| A17-3 (VPA2) - A27-56 (VPA2) | Always | Below 1 Ω |
| A17-2 (EPA2) - A27-60 (EPA2) | Always | Below 1 Ω |
| A17-1 (VCP2) - A27-59 (VCP2) | Always | Below 1 Ω |
| A17-6 (VPA) or A27-55 (VPA) - Body ground | Always | 10 kΩ or higher |
| A17-5 (EPA) or A27-58 (EPA) - Body ground | Always | 10 kΩ or higher |
| A17-4 (VCPA) or A27-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A17-3 (VPA2) or A27-56 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A17-2 (EPA2) or A27-60 (EPA2) - Body ground | Always | 10 kΩ or higher |
| A17-1 (VCP2) or A27-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the APP sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A17-4 (VCPA) - A17-5 (EPA) | Ignition switch ON | 4.5 to 5.5 V |
| A17-1 (VCP2) - A17-2 (EPA2) | Ignition switch ON | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ASSEMBLY |
Replace the accelerator pedal assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output | A |
| No DTC is output | B |
|
| ||||
| A | ||
| ||