Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

C172609E07

  1. Disconnect the DA, DB and DD main body ECU connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DA-1 - Body ground
    B - Body ground
    Battery power supply
    Always
    11 to 14 V
    DB-13 (BECU) - Body ground
    GR - Body ground
    Battery power supply
    Always
    11 to 14 V
    DD-62 (GND1, 2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the main body ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
DD-43 - DD-62 (GND1, 2)
LG - W-B
IG power supply
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
H2-10 (LIN2) - DD-62 (GND1, 2)
V - W-B
LIN communication signal
Ignition switch ON
Signal waveform
H2-14 (RWMR) - DD-62 (GND1, 2)
BE - W-B
Rear washer motor operation signal
Ignition switch ON and rear washer motor OFF
11 to 14 V
Ignition switch ON and rear washer motor ON
Below 1 V
H3-2 (RWIN) - DD-62 (GND1, 2)
L - W-B
Rear wiper switch signal
Ignition switch ON and rear wiper switch OFF
11 to 14 V
Ignition switch ON and wiper switch LO
Below 1 V
H3-9 (RWON) - DD-62 (GND1, 2)
W - W-B
Rear wiper switch signal
Ignition switch ON and rear wiper switch OFF
11 to 14 V
Ignition switch ON and rear wiper switch HI
Below 1 V
H4-7 (RWSW) - DD-62 (GND1, 2)
Y - W-B
Rear washer switch signal
Ignition switch ON and rear washer switch OFF
11 to 14 V
Ignition switch ON and rear washer switch ON
Below 1 V
DD-23 (HRLY) - DD-62 (GND1, 2)
SB - W-B
Headlight LO signal
Headlight LO switch OFF
11 to 14 V
Headlight LO switch ON
Below 1 V
DB-12 (IG) - DD-62 (GND1, 2)
Y - W-B
Headlight cleaner control relay IG signal
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
If the result is not as specified, there may be a malfunction on the wire harness side.

CHECK BACK DOOR ECU
If the result is not as specified, there may be a malfunction on the wire harness side.

E162515E01

  1. Disconnect the V2 and V3 back door ECU connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-1 (BDR) - Body ground
    SB - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    V2-7 (BECU) - Body ground
    GR - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-8 (SIG) - Body ground
    Y - Body ground
    IG power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    V3-7 (BKUL) - V3-19 (KEYE)
    LG - BE
    Tail gate control switch signal
    Back door key cylinder turned UNLOCK
    Below 1 Ω
    V3-8 (BKL) - V3-19 (KEYE)
    G - BE
    Tail gate control switch signal
    Back door key cylinder turned LOCK
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the back door ECU connectors.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-16 (MPX1) - V2-6 (GND)
    Y - W-B
    LIN communication signal
    Ignition switch ON
    Signal waveform
    V2-21 (A UP) - V2-6 (GND)
    G - W-B
    Back door power window AUTO UP signal
    Ignition switch ON and back door power window switch OFF → AUTO UP
    Pulse generation → Below 1 V
    V2-22 (BUP) - V2-6 (GND)
    BE - W-B
    Back door power window UP signal
    Ignition switch ON and back door power window switch OFF → UP
    Pulse generation → Below 1 V
    V2-23 (BDN) - V2-6 (GND)
    V - W-B
    Back door power window DOWN signal
    Ignition switch ON and back door power window switch OFF → DOWN
    Pulse generation → Below 1 V
    V2-24 (A DN) - V2-6 (GND)
    L - W-B
    Back door power window AUTO DOWN signal
    Ignition switch ON and back door power window switch OFF → AUTO DOWN
    Pulse generation → Below 1 V
    V3-5 (BDUP) - V2-6 (GND)
    BE - W-B
    Back door power window UP operation signal
    Ignition switch ON and back door power window switch OFF → UP
    Below 1 V → 11 to 14 V
    V3-6 (BDDN) - V2-6 (GND)
    P - W-B
    Back door power window DOWN operation signal
    Ignition switch ON and back door power window switch OFF → DOWN
    Below 1 V → 11 to 14 V
    V3-1 (WIP-) - V2-6 (GND)
    P - W-B
    Rear wiper motor operation signal
    Ignition switch ON and rear wiper switch LO or HI
    Pulse generation
    V3-2 (WIP+) - V2-6 (GND)
    L - W-B
    Rear wiper motor operation signal
    Ignition switch ON and rear wiper switch LO or HI
    Pulse generation
    V3-16 (W) - V2-6 (GND)
    R - W-B
    Rear wiper reverse position switch signal
    Ignition switch ON and rear wiper switch LO or HI
    Pulse generation
    V3-17 (P) - V3-25 (SGND)
    V - G
    Rear wiper retractable position switch signal
    Ignition switch ON and rear wiper switch OFF → ON
    Below 1 V → Pulse generation
    V3-12 (DSV) - V3-23 (DSG)
    LG - SB
    Power supply for Hall-IC
    Ignition switch ON
    11 to 14 V
    V3-13 (DS1) - V3-23 (DSG)
    L - SB
    Back door power window glass position signal
    Back door power window operation
    Pulse generation
    V3-14 (DS2) - V3-23 (DSG)
    Y - SB
    Back door power window glass position signal
    Back door power window operation
    Pulse generation
    V3-19 (KEYE) - V2-6 (GND)
    BE - W-B
    Ground for Tail gate control switch
    Always
    Below 1 Ω
    V3-23 (DSG) - V2-6 (GND)
    SB - W-B
    Ground for Hall-IC
    Always
    Below 1 Ω
    V3-25 (SGND) - V2-6 (GND)
    G - W-B
    Ground for rear wiper reverse position and rear wiper retractable position switch
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK HEADLIGHT CLEANER CONTROL RELAY

E160100E01

  1. Disconnect the relay connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A32-3 (IG) - A32-4 (E)
    GR - W-B
    IG power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    A32-4(E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    A32-2 (H) - A32-4 (E)
    BR - W-B
    Headlight cleaner switch and headlight switch operation signal
    Headlight cleaner switch OFF
    Below 1 V
    Headlight switch OFF
    Below 1 V
    Headlight cleaner switch ON and headlight switch ON
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the relay connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A32-6 (PB) - A32-4 (E)
    R - W-B
    Headlight cleaner motor operation signal
    Headlight cleaner motor stopped
    11 to 14 V
    Headlight cleaner motor operating
    Below 1 V
    If the result is not as specified, the relay may have a malfunction.