Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM

TOYOTA PARKING ASSIST-SENSOR SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK CLEARANCE WARNING ECU ASSEMBLY

E285890E03

  1. Disconnect the H131 clearance warning ECU assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H131-11 (IG) - H131-16 (E)
    BE - W-B
    Power source (IG)
    Ignition switch ON, clearance sonar main switch OFF
    Below 1 V
    Ignition switch ON, clearance sonar main switch ON
    11 to 14 V
    H131-16 (E) - Body ground
    W-B - Body ground
    ECU ground
    Always
    Below 1 Ω

  3. Reconnect the H131 clearance warning ECU assembly connector.

  4. Measure the resistance, voltage and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H131-2 (ER) - H131-16 (E)
    Y - W-B
    Clearance warning buzzer
    Ignition switch ON, clearance sonar main switch ON, shift lever in R and sensor is detecting state (buzzer sounding)
    Pulse generation (See waveform 1)
    Buzzer not sounding
    11 to 14 V
    H131-3 (BOF) - H131-16 (E)
    V - W-B
    Ultrasonic sensor power source
    Ignition switch ON, clearance sonar main switch ON
    7.2 to 8.8 V
    H131-5 (SOF) - H131-4 (E5)
    GR - G
    Front sensor communication signal
    Ignition switch ON, clearance sonar main switch ON, shift lever except R
    Pulse generation (See waveform 3)
    H131-4 (E5) - H131-16 (E)
    G - W-B
    ECU ground
    Always
    Below 1 Ω
    H131-6 (PL) - H131-16 (E)
    P - W-B
    Parking position signal
    Ignition switch ON, shift lever not in P position
    Below 1.5 V
    Ignition switch ON, shift lever in P position
    7 V or higher
    H131-7 (L1) - H131-16 (E)
    G - W-B
    Rear corner ultrasonic sensor RH
    Clearance warning indicator LED for rear corner sensor RH illuminates
    Below 3 V
    H131-8 (L2) - H131-16 (E)
    GR - W-B
    Rear corner ultrasonic sensor LH
    Clearance warning indicator LED for rear corner sensor LH illuminates
    Below 3 V
    H131-9 (L4) - H131-16 (E)
    V - W-B
    Front corner ultrasonic sensor RH
    Clearance warning indicator LED for front corner sensor RH illuminates
    Below 3 V
    H131-10 (L10) - H131-16 (E)
    R - W-B
    Clearance warning ECU signal
    Clearance warning indicator's operation indicator illuminates
    Below 3 V
    H131-12 (BOR) - H131-16 (E)
    R - W-B
    Ultrasonic sensor power source
    Ignition switch ON, clearance sonar main switch ON
    7.2 to 8.8 V
    H131-13 (E1) - H131-16 (E)
    P - W-B
    ECU ground
    Always
    Below 1 Ω
    H131-14 (SOR) - H131-13 (E1)
    LG - P
    Rear sensor communication signal
    Ignition switch ON, clearance sonar main switch ON, shift lever in R
    Pulse generation (See waveform 2)
    H131-17 (SPD) - H131-16 (E)
    V - W-B
    Vehicle speed signal
    Ignition switch ON, drive wheels are turned slowly
    Alternating between 1.5 to 4.5 V
    H131-20 (TL-) - H131-16 (E)
    L - W-B
    Illumination light
    Ignition switch ON and light control switch except TAIL
    Below 1.5 V
    Ignition switch ON and light control switch TAIL
    7 V or higher
    H131-21 (RL) - H131-16 (E)
    LG - W-B
    Reverse position signal
    Ignition switch ON, shift lever not in R
    Below 1.5 V
    Ignition switch ON, shift lever in R
    7 V or higher
    H131-23 (L3) - H131-16 (E)
    BE - W-B
    Rear center ultrasonic sensor
    Clearance warning indicator LED for rear center sensor illuminates
    Below 3 V
    H131-24 (L5) - H131-16 (E)
    LG - W-B
    Front corner ultrasonic sensor LH
    Clearance warning indicator LED for front corner sensor LH illuminates
    Below 3 V



  5. E285889E01
  6. Using an oscilloscope, check waveform 1.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    H131-2 (ER) - H131-16 (E)
    Tool Setting
    2 V/DIV., 500 μsec./DIV.
    Condition
    Ignition switch ON, clearance sonar main switch ON, shift lever in R and sensor is detecting state (buzzer sounding)



  7. E235241E01
  8. Using an oscilloscope, check waveform 2.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    H131-14 (SOR) - H131-13 (E1)
    Tool Setting
    5 V/DIV., 1 msec.
    Condition
    Ignition switch ON, clearance sonar main switch ON, shift lever in R



  9. E235241E01
  10. Using an oscilloscope, check waveform 3.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    H131-5 (SOF) - H131-4 (E5)
    Tool Setting
    5 V/DIV., 1 msec.
    Condition
    Ignition switch ON, clearance sonar main switch ON, shift lever except R