Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY


    A149190E01
  1. Apply gasoline or spindle oil to a new O-ring and install it to the injector.

    NOTICE:
    Make sure that there is no damage or foreign material in the groove of the injector when installing the O-ring.



    A161427E01
  1. Connect the injector connector.



    A161479E01
  1. Install the injector to the fuel delivery pipe as shown in the illustration.

    NOTICE:
    1. Make sure that there are no scratches or foreign matter in or around the insertion hole of the fuel delivery pipe.
    2. When inserting the injector, be careful not to damage the O-ring.
    3. Attach the part of the injector labeled B between the parts of the fuel delivery pipe labeled A.



    A214319E03
  1. Check that each injector is installed to the fuel delivery pipe facing the direction shown in the illustration.



2. INSTALL NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY


    A256331
  1. Install the 2 spacers and 4 insulators to the cylinder head LH.

  1. Install the fuel delivery pipe (with injectors) to the cylinder head LH.



  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


    NOTICE:
    A163659E01
    Make sure that the part of the injector labeled B is between the parts of the fuel delivery pipe labeled A.

  1. Connect the No. 7 wire harness connector.



3. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
  1. Install the No. 1 engine cover.



4. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


    A256330
  1. Install the 2 spacers and 4 insulators to the cylinder head RH.

  1. Install the fuel delivery pipe (with injectors) to the cylinder head RH.



  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


    NOTICE:
    A163659E01
    Make sure that the part of the injector labeled B is between the parts of the fuel delivery pipe labeled A.



5. INSTALL NO. 3 ENGINE COVER
  1. Install the No. 3 engine cover.



6. CONNECT NO. 3 VENTILATION HOSE


    A161422
  1. Connect the No. 6 wire harness connector.

  1. Connect the No. 3 ventilation hose.



7. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


    A308885
  1. Connect the No. 1 fuel pipe to the No. 2 fuel delivery pipe (for quick type B) (Click here).

  1. Attach the clamp.



8. CONNECT FUEL TUBE SUB-ASSEMBLY


    A161415
  1. Connect the fuel tube to the No. 2 fuel delivery pipe (for quick type A) (Click here).



    A256329
  1. Connect the fuel tube to the fuel delivery pipe (for quick type A) (Click here).



9. CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY


    A161418
  1. Connect the No. 2 fuel tube to the fuel pressure regulator (for quick type A) (Click here).



10. INSTALL AIR CLEANER HOSE ASSEMBLY
  1. Install the air cleaner hose assembly and tighten the 2 hose clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the vacuum hose to the air cleaner hose assembly.

  1. Connect the ventilation hose to the air cleaner hose assembly, and slide the clamp to secure the hose.



11. INSPECT FOR FUEL LEAK
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  1. Turn the intelligent tester main switch ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.



12. INSTALL V-BANK COVER


    A307791E01
  1. Attach the 2 V-bank cover hooks to the No. 1 V-bank cover bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover sub-assembly to attach the pins.
    Text in Illustration 
    *1
    V-bank Cover Grommet
    *2
    Pin
    *3
    No. 1 V-bank Cover Bracket
    *4
    V-bank Cover Hook