SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, use the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | Speed indicated on speedometer. |
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 650 to 750 rpm: Idling | - |
| Calculate Load | Calculated load by ECM/ Min.: 0%, Max.: 100% |
| - |
| Vehicle Load | Vehicle load/ Min.: 0%, Max.: 25700% | Actual vehicle load | - |
| MAF | Air flow rate from Mass Air Flow (MAF) meter/ Min.: 0 gm/s Max.: 655.35 gm/s | 3.4 to 6.2 gm/s: Idling | If the value approximately 0.0 gm/s:
|
| Atmosphere Pressure | Atmospheric pressure/ Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1912.6 mmHg) | Equivalent to atmospheric pressure (absolute pressure) | - |
| Coolant Temp | Engine coolant temperature/ Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | If the value -40°C (-40°F): sensor circuit open. If the value 140°C (284°F): sensor circuit shorted. |
| Intake Air | Intake air temperature/ Min.: -40°C (-40°F), Max.: 140°C (284°F) | Equivalent to ambient air temperature | If the value -40°C (-40°F): sensor circuit open. If the value 140°C (284°F): sensor circuit shorted. |
| Engine Run Time | Engine run time/ Min.: 0 s, Max.: 65535 s | Time after engine start | Service data |
| Initial Engine Coolant Temp | Initial engine coolant temperature/ Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | Close to ambient air temperature | Service data |
| Initial Intake Air Temp | Initial intake air temperature/ Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | Close to ambient air temperature | Service data |
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | - |
| Accelerator Position | Accelerator pedal position/ Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | - |
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position (APP) No. 1/ Min.: 0%, Max.: 100% | 10 to 22%: accelerator pedal is released 54 to 86%: accelerator pedal is fully depressed | - |
| Accel Sens. No.2 Volt % | Absolute APP No. 2/ Min.: 0%, Max.: 100% | 12 to 42%: accelerator pedal is released 66 to 98%: accelerator pedal is fully depressed | - |
| Accel Sensor Out No. 1 | Accelerator pedal position sensor No. 1 voltage/ Min.: 0 V, Max.: 4.980 V | 0.5 to 1.1 V: accelerator pedal is released 2.6 to 4.5 V: accelerator pedal is fully depressed | - |
| Accel Sensor Out No. 2 | Accelerator pedal position sensor No. 2 voltage/ Min.: 0 V, Max.: 4.980 V | 1.2 to 2.0 V: accelerator pedal is released 3.4 to 4.7 V: accelerator pedal is fully depressed | - |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting idle/ ON or OFF | ON: Idling | - |
| Accel Fully Close Learn #1 | Accelerator fully closed learning value No. 1/ Min.: 0, Max.: 124.5 deg | - | ETCS service data |
| Accel Fully Close Learn #2 | Accelerator fully closed learning value No. 2/ Min.: 0, Max.: 124.5 deg | - | ETCS service data |
| Throttle Sensor Volt % | Throttle valve opening percentage according to throttle position sensor/ Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA1 |
| Throttl Sensor #2 Volt % | Throttle valve opening percentage according to throttle position sensor No. 2/ Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA2 |
| ST1 | Brake pedal signal/ ON or OFF | ON: Brake pedal depressed | - |
| System Guard | System guard/ ON or OFF | - | ETCS service data |
| Open Side Malfunction | Open side malfunction/ ON or OFF | - | ETCS service data |
| Throttle Idle Position | Whether or not throttle position sensor detecting idling/ ON or OFF |
| - |
| Throttle Require Position | Required throttle position/ Min.: 0 V, Max.: 4.980 V | 0.5 to 1.1 V: Idling | - |
| Throttle Sensor Position*1 | Throttle position sensor/ Min.: 0%, Max.: 100% |
| Recognition value for throttle opening angle on ECM |
| Throttle Position No. 1 | Throttle position No. 1 output voltage/ Min.: 0 V, Max.: 4.980 V |
| - |
| Throttle Position No. 2 | Throttle position No. 2 output voltage/ Min.: 0 V, Max.: 4.980 V |
| - |
| Throttle Position Command | Throttle position command value/ Min.: 0 V, Max.: 4.980 V | 0.5 to 4.8 V | - |
| Throttle Sens Open Pos #1 | Throttle sensor opener position No. 1/ Min.: 0 V, Max.: 4.980 V | 0.6 to 1.4 V | ETCS service data |
| Throttle Sens Open Pos #2 | Throttle sensor opener position No. 2/ Min.: 0 V, Max.: 4.980 V | 1.7 to 2.5 V | ETCS service data |
| Throttle Motor Current | Throttle actuator current/ Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling | ETCS service data |
| Throttle Motor DUTY | Throttle actuator/ Min.: 0%, Max.: 100% | 10 to 22%: Idling after engine warmed up | ETCS service data |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open)/ Min.: 0%, Max.: 255% | 0 to 40%: During idling | ETCS service data |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close)/ Min.: 0%, Max.: 255% | 0 to 40%: During idling | ETCS service data |
| Throttle Fully Close Learn | Throttle valve fully closed (learned value)/ Min.: 0, Max.: 4.980 V | 0.4 to 1.0 V: Accelerator pedal released | - |
| +BM Voltage | +BM voltage/ Min.: 0, Max.: 79.988 V | 11 to 14 V: Ignition switch ON and system normal | ETCS service data |
| Actuator Power Supply | Actuator power supply/ ON or OFF | ON: Idling | ETCS service data |
| Throttle Position | Throttle valve opening angle/ Min.: 0 deg, Max.: 499.99 deg | - | For use when engine stall, starting problems or rough idle is present. |
| ISC Flow | Flow rate calculated using information from each sensor/ Min.: 0 L/s, Max.: 79.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| ISC Position | Requested opening amount calculated using ISC control/ Min.: 0 deg, Max.: 499.99 deg | - | For use when engine stall, starting problems or rough idle is present. |
| ISC Feedback Value | ISC feedback compensation amount/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| ISC Learning Value | ISC learned compensation amount/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| Electric Load Feedback Val | Compensation flow rate according to electrical load/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| Air Conditioner FB Val | Compensation flow rate according to air conditioner load/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| PS Feedback Val | Compensation flow rate according to power steering load/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| Low Revolution Control | Low engine speed control operation state/ ON or OFF | - | For use when engine stall, starting problems or rough idle is present. |
| Neutral Control | Neutral control operation state/ ON or OFF | - | For use when engine stall, starting problems or rough idle is present. |
| N Range Status | Shift lever N status/ ON or OFF | - | For use when engine stall, starting problems or rough idle is present. |
| Eng Stall Control FB Flow | Intake air compensation flow rate/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| Deposit Loss Flow | Flow loss due to deposits/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| Fuel Pump Duty | Fuel pump duty/ Min.: 0%, Max.: 399.99% | Idling: 33% | - |
| Injector (Port) | Injection period of the No. 1 cylinder/ Min.: 0 μs, Max.: 65535 μs | 2000 to 4000 μs: idling | - |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1)/ Min.: 0 ml, Max.: 2.047 ml | 0 to 0.5 ml | Quantity of fuel injection volume for 10 times |
| Current Fuel Type | Status of the current fuel type | Gasoline/petrol | - |
| EVAP (Purge) VSV | Purge VSV control duty/ Min.: 0%, Max.: 100% | 0 to 100%: During idling | Order signal from ECM |
| Evap Purge Flow | Purge flow/ Min.: 0%, Max.: 399.9% | 0 to 100%: Idling | - |
| Purge Density Learn Value | Learning value of purge density/ Min.: -200, Max.: 199.993 | Idling: -40 to 0% | Service data |
| Vapor pressure (calculated) | Calculated EVAP system pressure/ Min.: -720.896 kPa (-5407.167 mmHg), Max.: 720.874 kPa (5407.002 mmHg) | Approximately 100 kPa (750 mmHg): Ignition switch ON | - |
| EVAP Purge VSV | VSV status for control/ ON or OFF | - | - |
| Purge Cut VSV Duty | Purge cut VSV duty/ Min.: 0%, Max.: 399.9% | - | - |
| Target Air-Fuel Ratio | Air fuel ratio/ Min.: 0, Max.: 1.999 | 0.8 to 1.2: During idling | - |
| AF Lambda B1S1 | Output air fuel ratio associated with the Bank 1 Sensor 1/ Min.: 0, Max.: 1.999 |
| - |
| AF Lambda B2S1 | Output air fuel ratio associated with the Bank 2 Sensor 1/ Min.: 0, Max.: 1.999 |
| - |
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/ Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| AFS Voltage B2S1 | Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/ Min.: 0 V, Max.: 7.999 V | 2.8 to 3.8 V: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| AFS Current B1S1 | Air fuel ratio sensor current Bank 1 Sensor 1/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor. |
| AFS Current B2S1 | Air fuel ratio sensor current (for Bank 2 Sensor 1)/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output current of sensor. |
| A/F Heater Duty #1 | A/F heater duty ratio (for Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| A/F Heater Duty #2 | A/F heater duty ratio (for Bank 2)/ Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| O2S B1S2 | Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/ Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 70 km/h (44 mph) | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| O2S B2S2 | Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/ Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving 70 km/h (44 mph) | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| O2S Impedance B1S2 | Sub heated oxygen sensor impedance (Bank 1 Sensor 2)/ Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm | After driving approx. 10 min. in urban area |
| O2S Impedance B2S2 | Sub heated oxygen sensor impedance (Bank 2 Sensor 2)/ Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm | After driving approx. 10 min. in urban area |
| O2 Heater B1S2 | Heated oxygen sensor heater for bank 1 sensor 2/ Not Act or Active | - | - |
| O2 Heater B2S2 | Heated oxygen sensor heater for bank 2 sensor 2/ Not Act or Active | - | - |
| O2 Heater Curr Val B1S2 | Heated oxygen sensor current for bank 1 sensor 2/ Min.: 0 A, Max.: 4.9 A | - | - |
| O2 Heater Curr Val B2S2 | Heated oxygen sensor current for bank 2 sensor 2/ Min.: 0 A, Max.: 4.9 A | - | - |
| Short FT #1 | Short-term fuel trim of Bank 1/ Min.: -100%, Max.: 99.200% | -20 to +20% | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio. |
| Long FT #1 | Long-term fuel trim of Bank 1/ Min.: -100%, Max.: 99.200% | -15 to +15% |
|
| A/F Learn Value Idle #1 | Air fuel ratio learned value for idling (for Bank 1)/ Min.: -50%, Max.: 49.6% | -15 to +15% | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
| A/F Learn Value Low #1 | Air fuel ratio learned value for low engine loads (for Bank 1)/ Min.: -50%, Max.: 49.6% | -15 to +15% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid1 #1 | Air fuel ratio learned value for midsized engine loads 1 (for Bank 1)/ Min.: -50%, Max.: 49.6% | -15 to +15% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid2 #1 | Air fuel ratio learned value for midsized engine loads 2 (for Bank 1)/ Min.: -50%, Max.: 49.6% | -15 to +15% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High #1 | Air fuel ratio learned value for high engine loads (for Bank 1)/ Min.: -50%, Max.: 49.6% | -15 to +15% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| Total FT #1 | Total fuel trim of bank 1 Average value for fuel trim system of Bank 1/ Min.: -0.5, Max.: 0.496 | -0.2 to 0.2 V: Idling | - |
| Short FT #2 | Short-term fuel trim of Bank 2/ Min.: -100%, Max.: 99.200% | -20 to +20% | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at stoichiometric air-fuel ratio. |
| Long FT #2 | Long-term fuel trim of Bank 2/ Min.: -100%, Max.: 99.200% | -15 to +15% |
|
| A/F Learn Value Idle #2 | Air fuel ratio learned value for idling (for Bank 2) Min.: -50%, Max.: 49.6% | -15 to +15% | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
| A/F Learn Value Low #2 | Air fuel ratio learned value for low engine loads (for Bank 2) Min.: -50%, Max.: 49.6% | -15 to +15% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid1 #2 | Air fuel ratio learned value for midsized engine loads 1 (for Bank 2) Min.: -50%, Max.: 49.6% | -15 to +15% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid2 #2 | Air fuel ratio learned value for midsized engine loads 2 (for Bank 2) Min.: -50%, Max.: 49.6% | -15 to +15% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High #2 | Air fuel ratio learned value for high engine loads (for Bank 2) Min.: -50%, Max.: 49.6% | -15 to +15% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| Total FT #2 | Total fuel trim of bank 2 Average value for fuel trim system of Bank 2/ Min.: -0.5, Max.: 0.496 | -0.2 to 0.2 V: Idling | - |
| Fuel System Status #1 | Fuel system status (Bank 1)/ OL, CL, OLDrive, OLFault or CLFault | CL: Idling after warming up |
|
| Fuel System Status #2 | Fuel system status (Bank 2)/ OL, CL, OLDrive, OLFault or CLFault | CL: Idling after warming up |
|
| IGN Advance | Ignition timing advance for No. 1 cylinder/ Min.: -64 deg., Max.: 63.5 deg. | BTDC 5 to 15°: Idling | - |
| Knock Feedback Value | Feedback value of knocking/ Min.: -1024° CA, Max.: 1023.9° CA | -22 to 0° CA: Driving, 70 km/h (44 mph) | Service data |
| Knock Correct Learn Value | Correction learning value of knocking/ Min.: -1024° CA, Max.: 1023.9° CA | 0 to 22° CA: Driving, 70 km/h (44 mph) | Service data |
| Idle Spark Advn Ctrl #1 | Individual cylinder timing advance compensation amount (No. 1): Min.: 0°CA, Max.: 15.93°CA | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #2 | Individual cylinder timing advance compensation amount (No. 2): Min.: 0°CA, Max.: 15.93°CA | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #3 | Individual cylinder timing advance compensation amount (No. 3): Min.: 0°CA, Max.: 15.93°CA | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #4 | Individual cylinder timing advance compensation amount (No. 4): Min.: 0°CA, Max.: 15.93°CA | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #5 | Individual cylinder timing advance compensation amount (No. 5): Min.: 0°CA, Max.: 15.93°CA | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #6 | Individual cylinder timing advance compensation amount (No. 6): Min.: 0°CA, Max.: 15.93°CA | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #7 | Individual cylinder timing advance compensation amount (No. 7): Min.: 0°CA, Max.: 15.93°CA | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #8 | Individual cylinder timing advance compensation amount (No. 8): Min.: 0°CA, Max.: 15.93°CA | - | For use when engine stall, starting problems or rough idle is present. |
| ACIS VSV | VSV status for ACIS control/ ON or OFF | - | - |
| VVT Control Status #1 | Variable valve timing (VVT) control status (Bank 1)/ ON or OFF | - | - |
| VVT Control Status #2 | VVT control status (Bank 2)/ ON or OFF | - | - |
| VVT Advance Fail | VVT control failure status/ ON or OFF | ON: VVT control failure | - |
| VVT Aim Angle #1*2 | VVT aim angle (Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 80% | VVT duty signal value during intrusive operation. |
| VVT Change Angle #1*2 | VVT change angle (Bank 1)/ Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 5 DegFR: Idling | Displacement angle during intrusive operation. |
| VVT OCV Duty #1*2 | VVT OCV operation duty (Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 100% | Requested duty value for intrusive operation. |
| VVT Aim Angle #2*2 | VVT aim angle (Bank 2)/ Min.: 0%, Max.: 399.9% | 0 to 80% | VVT duty signal value during intrusive operation. |
| VVT Change Angle #2*2 | VVT change angle (Bank 2)/ Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 5 DegFR: Idling | Displacement angle during intrusive operation. |
| VVT OCV Duty #2*2 | VVT OCV operation duty (Bank 2)/ Min.: 0%, Max.: 399.9% | 0%: Idling | Requested duty value for intrusive operation. |
| VVT Ex Hold Lrn Val #1*2 | VVT exhaust hold duty ratio learning value (Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 80% | VVT duty signal value during intrusive operation. |
| VVT Ex Chg Angle #1*2 | VVT exhaust change angle (Bank 1)/ Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 40 DegFR: Idling | Displacement angle during intrusive operation. |
| VVT Ex OCV Duty #1*2 | VVT exhaust OCV duty (Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 100%: Idling | Requested duty value for intrusive operation. |
| VVT Ex Hold Lrn Val #2*2 | VVT exhaust hold duty ratio learning value (Bank 2)/ Min.: 0%, Max.: 399.9% | 0 to 80% | VVT duty signal value during intrusive operation. |
| VVT Ex Chg Angle #2*2 | VVT exhaust change angle (Bank 2)/ Min.: 0 DegFR, Max.: 639.9 DegFR | 0 to 40 DegFR: Idling | Displacement angle during intrusive operation. |
| VVT Ex OCV Duty #2*2 | VVT exhaust OCV duty (Bank 2)/ Min.: 0%, Max.: 399.9% | 0 to 100%: Idling | Requested duty value for intrusive operation. |
| VN Turbo Type | Variable nozzle turbo type/ Not Avl or Commo or Vacuum or CAN Com | Not Avl (Unused) | - |
| Catalyst Temp B1S1 | Catalyst temperature (Bank 1, Sensor 1)/ Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) | - | - |
| Catalyst Temp B2S1 | Catalyst temperature (Bank 2, Sensor 1)/ Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) | - | - |
| Catalyst Temp B1S2 | Catalyst temperature (Bank 1, Sensor 2)/ Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) | - | - |
| Catalyst Temp B2S2 | Catalyst temperature (Bank 2, Sensor 2)/ Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F) | - | - |
| Starter Signal | Starter signal/ Open or Close | Open: Cranking | - |
| Starter Control | Starter switch status/ ON or OFF | ON: Cranking | - |
| Power Steering Signal | Power steering switch signal/ ON or OFF | - | - |
| Starter Relay | Starter relay status/ ON or OFF | ON: Cranking | - |
| ACC Relay | Acc relay status/ ON or OFF | ON: Cranking | - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | ON: P or N position | - |
| Transfer L4 | L4 status of the transfer/ ON or OFF | ON: 4WD control switch in 4L position | - |
| Stop Light Switch | Stop light switch/ ON or OFF | ON: Brake pedal is depressed | - |
| A/C Signal | A/C switch status/ ON or OFF | ON: A/C ON | - |
| Closed Throttle Position SW | Closed throttle position switch/ ON or OFF |
| - |
| Fuel Cut Condition | Fuel cut condition/ ON or OFF | ON: Fuel cut operating | - |
| Immobiliser Communication | Immobiliser communication/ ON or OFF | ON: Normal | - |
| Check Mode | Check mode/ ON or OFF | ON: Check mode ON | Refer to Check Mode Procedure (Click here). |
| SPD Test Result | Check mode result for vehicle speed sensor/ Compl or Incmpl | - | - |
| Misfire Test Result | Check mode result for misfire monitor/ Compl or Incmpl | - | - |
| OXS1 Test Result | Check mode result for heated oxygen sensor (Bank 1)/ Compl or Incmpl | - | - |
| OXS2 Test Result | Check mode result for heated oxygen sensor (Bank 2)/ Compl or Incmpl | - | - |
| A/F Test Results #2 | Check mode result for air fuel ratio sensor (Bank 2)/ Compl or Incmpl | - | - |
| A/F Test Results #1 | Check mode result for air fuel ratio sensor (Bank 1)/ Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor/ Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor/ Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| A/C Monitor | A/C monitor/ Not Avl or Avail | - | - |
| A/C Monitor | A/C monitor: Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor/ Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor/ Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor/ Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor/ Compl or Incmpl | - | - |
| Component Monitor ENA | Comprehensive component monitor/ Unable or Enable | - | - |
| Component Monitor CMPL | Comprehensive component monitor/ Compl or Incmpl | - | - |
| Fuel System Monitor ENA | Fuel system monitor/ Unable or Enable | - | - |
| Fuel System Monitor CMPL | Fuel system monitor/ Compl or Incmpl | - | - |
| Misfire Monitor ENA | Misfire monitor/ Unable or Enable | - | - |
| Misfire Monitor CMPL | Misfire monitor/ Compl or Incmpl | - | - |
| EGR/VVT Monitor ENA | EGR monitor/ Unable or Enable | - | - |
| EGR/VVT Monitor CMPL | EGR monitor/ Compl or Incmpl | - | - |
| Heater Monitor ENA | O2S (A/FS) heater monitor/ Unable or Enable | - | - |
| Heater Monitor CMPL | O2S (A/FS) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor ENA | O2S (A/FS) monitor/ Unable or Enable | - | - |
| O2S(A/FS) Monitor CMPL | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| A/C Monitor ENA | A/C monitor/ Unable or Enable | - | - |
| A/C Monitor CMPL | A/C monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor ENA | 2nd air monitor/ Unable or Enable | - | - |
| 2nd Air Monitor CMPL | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor ENA | EVAP monitor/ Unable or Enable | - | - |
| EVAP Monitor CMPL | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Cat Monitor ENA | Heated catalyst monitor/ Unable or Enable | - | - |
| Heated Cat Monitor CMPL | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor ENA | Catalyst monitor/ Unable or Enable | - | - |
| Catalyst Monitor CMPL | Catalyst monitor/ Compl or Incmpl | - | - |
| TC Terminal | TC terminal status/ ON or OFF | - | - |
| # Codes (Include History) | Number of codes/ Min.: 0, Max.: 255 | - | Number of detected DTCs |
| MIL | MIL status/ ON or OFF | ON: MIL ON | - |
| MIL ON Run Distance | MIL ON run distance/ Min.: 0 km, Max.: 65535 km | Distance after DTC detected | - |
| Running Time from MIL ON | Running time from MIL ON/ Min.: 0 min, Max.: 65535 min | Equivalent to running time after MIL was ON | - |
| Time after DTC Cleared | Time after DTC cleared/ Min.: 0 min, Max.: 65535 min | Equivalent to time after DTCs were cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared/ Min.: 0 km, Max.: 65535 km | Equivalent to drive distance after DTCs were cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared/ Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTC cleared |
| Dist Batt Cable Disconnect | Distance from battery cable disconnected/ Min.: 0 km, Max.: 65535 km | - | - |
| OBD Requirements | OBD requirement | OBD2 | - |
| Number of Emission DTC | Emission related DTCs/ Min.: 0, Max.: 127 | - | Number of emission related DTCs |
| TC and TE1 | TC and TE1 terminal of DLC3/ ON or OFF | - | - |
| Ignition Trig. Count | Ignition counter/ Min.: 0, Max.: 65535 | 0 to 800 | - |
| Cylinder #1 Misfire Count to Cylinder #8 Misfire Count | Misfire count of the cylinder 1 to 8/ Min.: 0, Max.: 255 | 0 | - |
| All Cylinders Misfire Count | All cylinders misfire count/ Min.: 0, Max.: 255 | 0 to 35 | - |
| Multi Cylinders Misfire Count | Multiple cylinder misfire count/ Min.: 0 Max.: 65535 | 0 to 65535 | - |
| Misfire RPM | Engine speed for first misfire range/ Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: Misfire 0 | - |
| Misfire Load | Engine load for first misfire range/ Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: Misfire 0 | - |
| Misfire Margin | Misfire monitoring/ Min.: -128%, Max.: 127% | -100 to 99.2% | The misfire detecting margin |
| Catalyst OT MF F/C | Catalyst over temperature misfire prevention F/C/ Not Avl or Avail | Avail: Cat OT MF F/C available Not Avl: Cat OT MF F/C not available | - |
| Cat OT MF F/C History | Catalyst over temperature misfire prevention F/C history/ ON or OFF | OFF: Fuel cut operation does not exist | - |
| Cat OT MF F/C Cylinder #1 | Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #2 | Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #3 | Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #4 | Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #5 | Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #6 | Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #7 | Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #8 | Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Engine Speed (Starter Off) | Engine speed when starter off/ Min.: 0 rpm, Max.: 51199 rpm | - | For use when engine stall, starting problems or rough idle is present. |
| Starter Count | Number of times starter turned on after ignition switch turned to ON/ Min.: 0, Max.: 255 | - | For use when engine stall, starting problems or rough idle is present. |
| Run Dist of Previous Trip | Distance driven during previous trip/ Min.: 0 km, Max.: 655.35 km | - | Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
|
| Engine Starting Time | Time elapsed after engine started (interval between ignition switch ON and off)/ Min.: 0 ms, Max.: 655350 ms | - | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Coolant Temp | Engine coolant temperature during previous trip/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Intake Temp | Intake air temperature during previous trip/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Engine Oil Temperature | Engine oil temperature (estimated temperature)/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Eng Oil Temp | Engine oil temperature during previous trip/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Ambient Temp for A/C | Ambient temperature for A/C/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Ambient Temp | Ambient temperature during previous trip/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Engine Start Hesitation | History of hesitation during engine start/ ON or OFF | - | - |
| Low Rev for Eng Start | History of low engine speed after engine start/ ON or OFF | - | - |
| Minimum Engine Speed | Minimum engine speed/ Min.: 0 rpm, Max.: 51199 rpm | - | For use when engine stall, starting problems or rough idle is present. |
| Power Steering Pressure | Power steering oil pressure/ Min.: 0 MPa, Max.: 25.599 MPa | - | - |
| ACT VSV | A/C cut status for Active Test/ ON or OFF | - | - |
| Brake Override System | Brake Override System Status/ ON or OFF | ON: Brake override system operation | - |
| Idle Fuel Cut | Fuel cut idle/ ON or OFF | ON: Fuel cut operation | Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm. |
| FC TAU | Fuel cut TAU: Fuel cut during very light load/ ON or OFF | ON: Fuel cut operation | The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete. |
| Immobiliser Fuel Cut | Status of the immobiliser fuel cut/ ON or OFF | - | - |
| Immobiliser Fuel Cut History | Status of the immobiliser fuel cut history/ ON or OFF | - | - |
| Vehicle Spec Signal 1 | Status of the Vehicle Spec Judge Signal 1/ ON or OFF | - | - |
| Electrical Load Signal 1 | Electrical load signal/ ON or OFF | - | - |
| Electrical Load Signal 2 | Electrical load signal/ ON or OFF | - | - |
| Cruise Cancel Signal | Status of the cruise cancel signal/ ON or OFF | - | - |
| Model Code | Model code | - | Identifying the model code: USK5## |
| Engine Type | Engine type | - | Identifying the engine type: 3URFE |
| Cylinder Number | Number of cylinders/ Min.: 0, Max.: 255 | - | Identifying number of cylinders: 8 |
| Transmission Type | Transmission type | - | Identifying the transmission type: ECT 6th |
| Destination | Destination | - | Identifying the destination |
| Model Year | Model year/ Min.: 1900, Max.: 2155 | - | Identifying the model year: 20## |
| System Identification | System identification | - | Identifying the engine system: Gasoline (gasoline engine) |
| Engine Speed of Cyl #1 | Engine RPM for cylinder 1/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #2 | Engine RPM for cylinder 2/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #3 | Engine RPM for cylinder 3/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #4 | Engine RPM for cylinder 4/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #5 | Engine RPM for cylinder 5/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #6 | Engine RPM for cylinder 6/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #7 | Engine RPM for cylinder 7/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #8 | Engine RPM for cylinder 8/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Av Engine Speed of All Cyl | Engine RPM for all cylinders/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| SPD (NT) | Input shaft speed/ Min.: 0 rpm, Max.: 12750 rpm | Lock-up is
| Data is displayed in increments of 50 rpm |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Injection Volume | Change injection volume | Between -12.5% and 24.8% |
|
| Control the Injection Volume for A/F Sensor | Change injection volume | -12.5%/ 0%/12.5% |
|
| Activate the VSV for Intake Control | Activate VSV for intake control | ON/OFF | - |
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF | - |
| Control the A/C Cut Signal | Control A/C cut signal | ON/OFF | - |
| Control the Fuel Pump/Speed | Activate fuel pump | ON/OFF | This test is possible when the following conditions are met:
|
| Control the Fuel Pump Duty | Activate fuel pump | 25% / 80% | This test is possible when the following conditions are met:
|
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF |
|
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Prohibit the Catalyst OT Misfire prevent F/C | Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire | ON: Fuel cut is prohibited | Confirm that the Vehicle is Stopped and Engine Speed is 3000 rpm or less. |
| Activate the Starter Relay | Activate the starter relay | ON/OFF | Engine is stopped. |
| Activate the ACC Cut Relay | Activate the ACC CUT relay | ON/OFF | Engine is stopped. |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Close/Open Open: throttle valve opens slowly | This test is possible when the following conditions are met:
|
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Close/Open Open: throttle valve opens fast | |
| Control the VVT Linear (Bank 1) | Control Variable Valve Timing (VVT) [Bank 1] | -128 to 127% This value added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 1) | Turn on and off Oil Control Valve (OCV) | ON/OFF |
|
| Control the VVT Linear (Bank 2) | Control Variable Valve Timing (VVT) [Bank 2] | -128 to 127% This value added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 2) | Turn on and off Oil Control Valve (OCV) | ON/OFF |
|
| Control the VVT Exhaust Linear (Bank 1) | Control VVT (Bank 1) | -128 to 127% This value added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT Exhaust Linear (Bank 2) | Control VVT (Bank 2) | -128 to 127% This value added to present OCV control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the Cylinder #1 Fuel Cut | Cylinder #1 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #2 Fuel Cut | Cylinder #2 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #3 Fuel Cut | Cylinder #3 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #4 Fuel Cut | Cylinder #4 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #5 Fuel Cut | Cylinder #5 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #6 Fuel Cut | Cylinder #6 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #7 Fuel Cut | Cylinder #7 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the Cylinder #8 Fuel Cut | Cylinder #8 injector fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the All Cylinders Fuel Cut | All cylinder fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Check the Cylinder Compression*2 | Check the cylinder compression pressure | ON/OFF | Fuel injection and ignition stop in all cylinders. |