DTC P0617 Starter Relay Circuit High |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0617 | When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)
|
|

| 1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the intelligent tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
| ON | OFF |
| START | ON |
|
| ||||
| OK | ||
| ||
| 2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Disconnect the Park/Neutral Position (PNP) switch connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the intelligent tester when the ignition switch is turned to the ON and START positions.
| Starter Signal | Proceed to |
| Remains ON | A |
| OFF | B |
|
| ||||
| A | |
| 3.INSPECT ECM (STA TERMINAL VOLTAGE) |
Disconnect the ECM connector.
Disconnect the PNP switch connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Proceed to |
| A27-46 (STA) - Body ground | Ignition switch ON | Below 1.5 V | A |
| 11 to 14 V | B |
|
| ||||
| A | ||
| ||
| 4.INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the PNP switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4 (B) - 5 (L) | Except P or N | 10 kΩ or higher |
| 2 (RB) - 5 (L) | All positions | 10 kΩ or higher |
| Result | Proceed to |
| Short between 4 and 5 | A |
| Short between 2 and 5 | B |
| Within standard range | C |
|
| ||||
|
| ||||
| A | |
| 5.REPLACE PARK / NEUTRAL POSITION SWITCH ASSEMBLY |
Replace the park/neutral position switch (Click here).
| NEXT | |
| 6.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (AM2) - 7 (ST2) | Except above | 10 kΩ or higher |
| Ignition switch position START | Below 1 Ω |
|
| ||||
| OK | |
| 7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the intelligent tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
| ON | OFF |
| START | ON |
| Result | Proceed to |
| Outside standard range | A |
| Within standard range | B |
|
| ||||
| A | |
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM) |
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear DTCs (Click here).
Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P0617 is output | A |
| No DTC is output | B |
|
| ||||
| A | ||
| ||