Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)
  1. (a) Vehicle speed 20 km/h (12.4 mph) or more
  2. (b) Engine speed 1000 rpm or more
  3. (c) STA signal ON
  1. Park/Neutral Position (PNP) switch
  2. Starter relay circuit
  3. Ignition switch
  4. ECM

WIRING DIAGRAM


A159967E08


INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
    If the engine will not crank, proceed to the Problem Symptoms Table (Click here).
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the value displayed on the intelligent tester when the ignition switch is turned to the ON and START positions.

    OK:

    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Disconnect the Park/Neutral Position (PNP) switch connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the value displayed on the intelligent tester when the ignition switch is turned to the ON and START positions.

    Result 
    Starter Signal
    Proceed to
    Remains ON
    A
    OFF
    B



B
Go to step 4
A


3.INSPECT ECM (STA TERMINAL VOLTAGE)
  1. Disconnect the ECM connector.

  1. Disconnect the PNP switch connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Proceed to
    A27-46 (STA) - Body ground
    Ignition switch ON
    Below 1.5 V
    A
    11 to 14 V
    B



B
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PNP SWITCH - ST RELAY)
A

REPLACE ECM (Click here)  

4.INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch (Click here)


Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 6
A


5.REPLACE PARK / NEUTRAL POSITION SWITCH ASSEMBLY
  1. Replace the park/neutral position switch (Click here).


NEXT


6.INSPECT IGNITION SWITCH ASSEMBLY
B110407E06
  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (AM2) - 7 (ST2)
    Except above
    10 kΩ or higher
    Ignition switch position START
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the value displayed on the intelligent tester when the ignition switch is turned to the ON and START positions.

    OK:

    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON


    Result 
    Result
    Proceed to
    Outside standard range
    A
    Within standard range
    B



B
END
A


8.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM)

NEXT


9.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear DTCs (Click here).

  1. Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0617 is output
    A
    No DTC is output
    B



B
END
A

REPLACE ECM (Click here)