Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0102    Mass or Volume Air Flow Circuit Low Input

DTC    P0103    Mass or Volume Air Flow Circuit High Input

for Preparation Click here


DESCRIPTION

The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve.
The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.
Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A160257E01


DTC No.
DTC Detection Condition
Trouble Area
P0102
MAF meter voltage less than 0.2 V for 3 seconds
(1 trip detection logic)
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. ECM
P0103
MAF meter voltage more than 4.9 V for 3 seconds
(1 trip detection logic)
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. ECM

HINT:
When any of these DTCs are stored, check the air-flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Air Flow Rate (g/sec.)
Malfunction
Approximately 0.0
  1. Open in Mass Air Flow (MAF) meter power source circuit
  2. Open or short in VG circuit
160.0 or more
Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the MAF meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the MAF meter and stores a DTC.
Example:
When the sensor output voltage remains at less than 0.2 V, or more than 4.9 V for more than 3 seconds, the ECM stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

WIRING DIAGRAM


A164719E07


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

  1. Read the values displayed on the intelligent tester.
    Result 
    Mass Air Flow Rate (g/sec.)
    Proceed to
    0.0
    A
    160.0 or more
    B
    Between 1.0 and 160.0*
    C

    HINT:
    *: The value must change when the throttle valve is open or closed with the engine running.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
A148765E32
  1. Disconnect the MAF meter connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D3-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 5
OK


3.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter .



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A164720E21
  1. Disconnect the MAF meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D3-3 (VG) - D56-74 (VG)
    Always
    Below 1 Ω
    D3-2 (E2G) - D56-75 (E2G)
    Always
    Below 1 Ω
    D3-3 (VG) or D56-74 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY)
A160259E05
  1. Check the EFI NO. 2 fuse.

    1. Remove the EFI NO. 2 fuse from the engine room relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI NO. 2 fuse
      Always
      Below 1 Ω

    3. Reinstall the EFI NO. 2 fuse.

  1. Disconnect the MAF meter connector.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D3-1 (+B) - 1B-4
    Always
    Below 1 Ω
    D3-1 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A164720E18
  1. Disconnect the MAF meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D3-3 (VG) - D56-74 (VG)
    Always
    Below 1 Ω
    D3-2 (E2G) - D56-75 (E2G)
    Always
    Below 1 Ω
    D3-3 (VG) or D56-74 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
A148765E33
  1. Disconnect the MAF meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D3-2 (E2G) - Body ground
    Always
    Below 1 Ω



NG
REPLACE ECM (Click here)
OK

REPLACE MASS AIR FLOW METER (Click here)