Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR

REAR AIRBAG SENSOR > INSTALLATION

for Preparation Click here




1. INSTALL REAR AIRBAG SENSOR RH
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B193065
  1. Attach the guide to Install the rear airbag sensor.

  1. Install the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    CAUTION:
    1. If the rear airbag sensor LH has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the rear airbag sensor LH, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the rear airbag sensor.

  1. Connect the connector to the rear airbag sensor.



2. INSTALL REAR AIRBAG SENSOR LH

HINT:
Use the same procedure as for the RH side.



3. INSTALL REAR SIDE NO. 3 AIR DUCT


    E181294
  1. Install the air duct with the 2 clips.



4. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Standard)
  1. Connect the connector.

  1. Attach the 11 clips to install the quarter trim panel assembly.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B219907



    B190147
  1. Attach the 2 claws to install the cover.



    B190146
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Attach the 3 claws to install the outer lap belt anchor cover.



5. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Standard)
  1. Connect the connector.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222458



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



6. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)
  1. Connect the 3 connectors.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222459



    B190147
  1. Attach the 2 claws to install the cover.



    B190146
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Attach the 3 claws to install the outer lap belt anchor cover.



7. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)
  1. Connect the 5 connectors.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Attach the 2 clamps to install the wire harness.



  1. Install the 2 clips.


    B222460



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



8. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Attach the 5 clips and 4 claws to install the rear floor mat support plate.



9. INSTALL ROPE HOOK ASSEMBLY


    B190141
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B190139
  1. Attach the 2 claws to install the cover.



10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B190154E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    Pink
    LH side
    Purple



11. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



12. INSTALL REAR DOOR SCUFF PLATE RH


    B186666
  1. Attach the 2 claws and 5 clips to install the rear door scuff plate.

  1. Install the 2 bolts.



    B186665
  1. Attach the 6 claws, 5 clips and 2 guides to install the rear door scuff plate.

  1. Install the bolt.



13. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



14. INSTALL REAR FLOOR STEP NO. 1 COVER


    B191404
  1. Attach the 2 claws to install the rear floor step No. 1 cover.



15. INSTALL REAR FLOOR STEP NO. 2 COVER


    B193890
  1. Attach the 2 claws to the install the rear floor step No. 2 cover.



16. INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH


    B191794
  1. Attach the 2 clips and 5 claws to install the rear cushion hinge lower cover RH.



17. INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



18. INSTALL REAR NO. 2 SEAT ASSEMBLY RH
  1. for Manual Seat:
    Install the rear No. 2 seat assembly RH (Click here )

  1. for Power Seat:
    Install the rear No. 2 seat assembly RH (Click here )



19. INSTALL REAR NO. 2 SEAT ASSEMBLY LH
  1. for Manual Seat:
    Install the rear No. 2 seat assembly LH (Click here )

  1. for Power Seat:
    Install the rear No. 2 seat assembly LH (Click here )



20. INSTALL DECK BOARD BRACKET


    B190119
  1. Install the deck board bracket with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



21. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Install the deck board reinforcement with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



22. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Attach the 5 clips to install the No. 1 deck board.



23. INSTALL ROPE HOOK ASSEMBLY


    B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



24. INSTALL LUGGAGE COMPARTMENT TRIM BOX


    B190116
  1. Install the luggage compartment trim box with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B194633
  1. Install the 4 caps.



25. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B194608
  1. Attach the 4 guides to install the No. 2 deck board.



26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



27. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).