Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR

REAR AIRBAG SENSOR > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    B190118
  1. Raise the handle, detach the 4 guides and remove the No. 2 deck board.



3. REMOVE LUGGAGE COMPARTMENT TRIM BOX


    B194633
  1. Remove the 4 caps.



    B190116
  1. Remove the 4 bolts and luggage compartment trim box.



4. REMOVE ROPE HOOK ASSEMBLY


    B191405
  1. Remove the bolt and rope hook.

    HINT:
    Use the same procedure for both sides.



5. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Detach the 5 clips and remove the No. 1 deck board.



6. REMOVE DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Remove the 4 bolts and deck board reinforcement.



7. REMOVE DECK BOARD BRACKET


    B190119
  1. Remove the 2 bolts and deck board bracket.



8. REMOVE REAR NO. 2 SEAT ASSEMBLY RH
  1. for Manual Seat:
    Remove the rear No. 2 seat assembly RH (Click here )

  1. for Power Seat:
    Remove the rear No. 2 seat assembly RH (Click here )



9. REMOVE REAR NO. 2 SEAT ASSEMBLY LH
  1. for Manual Seat:
    Remove the rear No. 2 seat assembly LH (Click here )

  1. for Power Seat:
    Remove the rear No. 2 seat assembly LH (Click here )



10. REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH


    B191794
  1. Detach the 2 clips and 5 claws, and remove the rear seat cushion hinge lower cover.



11. REMOVE REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



12. REMOVE REAR FLOOR STEP NO. 1 COVER


    B191403E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



13. REMOVE REAR FLOOR STEP NO. 2 COVER


    B193052E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



14. REMOVE REAR DOOR SCUFF PLATE RH


    B186665
  1. Remove the bolt.

  1. Detach the 5 clips, 6 claws and 2 guides, and remove the rear door scuff plate front side.



    B186666
  1. Remove the 2 bolts.

  1. Detach the 5 clips and 2 claws, and remove the scuff plate rear side.



15. REMOVE REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



16. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B191804
  1. Remove the rear door opening weatherstrip.



17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



18. REMOVE ROPE HOOK ASSEMBLY

HINT:
Use the same procedure for both sides.



    B190140E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.



    B190141
  1. Remove the bolt and the rope hook.



19. REMOVE REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Detach the 5 clips and 4 claws, and remove the rear floor mat support plate.



20. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Standard)


    B190145
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the connector and remove the quarter trim panel.


    B219907



21. REMOVE QUARTER TRIM PANEL ASSEMBLY LH (for Standard)


    B193920
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B191818
  1. Remove the bolt and outer lap belt anchor.



    B191816
  1. Remove the bolt and outer lap belt anchor.



    B191817E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the connector and remove the quarter trim panel.


    B222458



22. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)


    B190145
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the 3 connectors and remove the quarter trim panel.


    B222459



23. REMOVE QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)


    B193920
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B191818
  1. Remove the bolt and outer lap belt anchor.



    B191816
  1. Remove the bolt and outer lap belt anchor.



    B191817E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 2 clamps and remove the wire harness.

  1. Detach the 11 clips and 2 clamps.



  1. Disconnect the 5 connectors and remove the quarter trim panel.


    B222460



24. REMOVE REAR SIDE NO. 3 AIR DUCT


    E181294
  1. Remove the 2 clips and the air duct.



25. REMOVE REAR AIRBAG SENSOR RH


    B193065
  1. Disconnect the connector from the rear airbag sensor.

    NOTICE:
    Disconnect the connector with the rear airbag sensor installed.

  1. Remove the bolt.

  1. Detach the guide and remove the rear airbag sensor.



26. REMOVE REAR AIRBAG SENSOR LH

HINT:
Use the same procedure as for the RH side.