REPAIR INSTRUCTION > INITIALIZATION |
| PROCEDURES NECESSARY WHEN CABLE IS DISCONNECTED/RECONNECTED TO BATTERY TERMINAL |
| Necessary Procedure | Procedure Details | Effect or Inoperative Function when Necessary Procedure is not Performed | Note |
| Power back door system initialization | To initialize, close the back door completely by hand. | Jam protection function | If the back door is closed when disconnecting the cable from the battery terminal, it is not necessary to reset it. |
| PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED |
| Replacement Part | Necessary Procedures | Effect or Inoperative Function when Necessary Procedure is not Performed | Note |
for AB60E
| Reset memory | Large shift shock | - |
for AB60F
| Reset memory | Large shift shock | - |
| Skid control ECU |
| ABS warning and slip indicator light illumination | - |
| Yaw rate sensor |
|
| - |
| Front Wheel Alignment Adjustment |
| ABS warning and slip indicator light illumination | Complete the adjustment of the steering wheel and wheel alignment, and then initialize the steering angle sensor. If the order is reversed, the steering wheel and wheel alignment will become misaligned. |
| Occupant classification ECU |
|
| - |
| Registration | Engine starting | Refer to the Service Bulletin for the registration procedure. |
| Register recognition code | Wireless door lock operation | - |
| Inner rear view mirror |
|
| - |
| Initialize the motor |
| - |
| Back power window regulator motor | Initialize the motor |
| - |
| Sliding roof drive gear (Sliding roof ECU) | Initialize sliding roof system |
| - |
| Initialize power back door system | Power back door system | - |
| RESET MEMORY (for AB60E) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.
| RESET MEMORY (for AB60F) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.
| CLEAR ZERO POINT CALIBRATION DATA (WHEN USING INTELLIGENT TESTER) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Select the skid control ECU to clear the zero point calibration date using the intelligent tester.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Reset Memory.
| PERFORM ZERO POINT CALIBRATION OF MASTER CYLINDER PRESSURE SENSOR AND DECELERATION SENSOR (WHEN USING INTELLIGENT TESTER) |
Enter Test Mode.
Turn the ignition switch off.
Check that the shift lever is in P or N and apply the parking brake.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Test Mode.
Obtain the zero points of the master cylinder pressure sensor and deceleration sensor.
Keep the vehicle stationary on a level surface for 1 second or more.
Check that DTC C1336 is cleared.
Turn the ignition switch off.
| CLEAR ZERO POINT CALIBRATION DATA (WHEN USING SST CHECK WIRE) |
Turn the ignition switch to ON.
![]() |
Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.
Check that the VSC OFF indicator light comes on.
Using a check wire, perform the zero point calibration of the deceleration sensor.
| PERFORM ZERO POINT CALIBRATION OF MASTER CYLINDER PRESSURE SENSOR AND DECELERATION SENSOR (WHEN USING SST CHECK WIRE) |
Enter Test Mode.
Turn the ignition switch off.
Check that the shift lever is in P or N and apply the parking brake.
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
Obtain the zero points of the master cylinder pressure sensor and deceleration sensor.
Keep the vehicle stationary on a level surface for 1 second or more.
Check that DTC C1336 is cleared.
Turn the ignition switch off.
| PERFORM INITIALIZATION OF STEERING ANGLE SENSOR |
Check that the steering wheel is in the centered position.
Disconnect the negative (-) battery terminal for more than 2 seconds.
Reconnect the negative (-) battery terminal.
| ZERO POINT CALIBRATION |
Zero point calibration procedures:
Check that all of the following conditions are met:
Adjust the seat position in accordance with the table below.
| Adjustment Item | Position |
| Slide Direction | Rearmost position |
| Reclining Angle | Upright position |
| Headrest Height | Lowest position |
| Lifter Height | Lowest position |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester on.
Enter the following menus: Body / Occupant Detection / Utility / Zero Point Calibration.
Perform the zero point calibration by following the prompts on the intelligent tester screen.
| SENSITIVITY CHECK |
Sensitivity check procedures:
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester on.
Enter the following menus: Body / Occupant Detection / Utility / Sensitivity Check.
Perform the sensitivity check by following the prompts on the intelligent tester screen.
Confirm that the beginning sensor reading is within the standard range.
Place a 30 kg (66.2 lb) weight (e.g. a lead mass) onto the front passenger seat.
Confirm that the sensitivity is within the standard range.
| DESCRIPTION OF CODE REGISTRATION |
| REGISTER RECOGNITION CODE (USING OR INTELLIGENT TESTER) |
Turn the ignition switch ON.
Enter the following menus: Body / Main Body / Wireless Registration.
Press both LOCK and UNLOCK switches between 1 to 1.5 seconds.
Press either switch for more than 1 second within 3 seconds.
Check the response to the registration completion.

Perform either of the following to complete the registration of recognition codes:
| REGISTER RECOGNITION CODE (USING SWITCH OPERATION) |
The following conditions must be met.
Insert and remove the key into / from the ignition key cylinder twice (Insert → Remove → Insert → Remove) within 5 seconds.
Perform the following operations within 40 seconds.
Close and open the driver side door twice (Close → Open → Close → Open).
Insert and remove the key into / from the ignition key cylinder (Insert → Remove).
Close and open the driver side door twice (Close → Open → Close → Open).
Insert the key into the ignition key cylinder and close all doors.
Perform the following operations within 40 seconds.
Turn the ignition switch from ON to OFF at approximately 1 second intervals. Operate the ignition switch according to the number of times shown below.

Remove the key from the ignition key cylinder.
Check the response of the selected mode within 5 seconds.

Within 40 seconds of completing the confirmation mode operation, press the LOCK and UNLOCK switches on the transmitter simultaneously.
After completing the above step, press a shingle switch (LOCK or UNLOCK) within 5 seconds.
After completing the above step, check the response to the registration completion within 3 seconds.

Perform either of the following to complete the registration of recognition codes:
| SELECT COMPASS DISPLAY MODE |
The compass switch allows you to select the Display or Non-display mode of the compass.
| SET ZONE |
Deviation between the "magnetic north" and "actual north" differs depending on the location. Therefore, adjustment of the magnetism is required. Because the magnetic condition differs depending on the area where the vehicle is used, it is necessary for each user to set the zone (refer to Compass Zone Map). The zone setting can be changed using the compass switch of the inner mirror.
| PERFORM CALIBRATION |
Because each vehicle has its own magnetic field, calibration should be performed for each individual vehicle. This compass function is used when storing the record of the vehicle's magnetic field.
| WHEN COMPASS IS MAGNETIZED |
The compass could be magnetized during shipping by vessels or freight cars. Therefore, ensure that calibration is performed properly before delivery. If driving the vehicle in a circle several times does not complete the calibration procedure, there may be a compass magnetization problem.

| Deviation Calibration Procedure |
![]() |
Turn the ignition switch to the "IG-ON" position and push and hold the "AUTO" switch for 6 seconds until the zone number appears on the display.
Push the "AUTO" switch to select the number of the zone where the vehicle is located.
See the map for zone reference.

| Circling Calibration Procedure |
![]() |
Start the engine and push and hold the "AUTO" switch for 9 seconds until "C" appears on the display.
![]() |
Drive the vehicle slowly at 8 km/h (5 mph) or lower in a circle.
If there is not enough space to drive in a circle, turn the car around in the following manner, doing two three-point turns in succession.
After driving in 1 to 3 circles in the above method, calibration is completed with the direction is shown on the display.
| INITIALIZATION PROCEDURE |
Press the rear power seat switch in the forward position until the third-row seat is completely folded (stowed).
With the third-row seat in the completely folded position (stored), hold the rear power seat switch in the forward position for 1 more second.
The buzzer sounds twice when the initialization is complete.
| INITIALIZATION RELEASE PROCEDURE |
While holding the fold seat switch in the return position, press the rear power seat switch in the forward position 5 times before 10 seconds elapse. This will complete the initialization release procedure.
| INITIALIZE POWER WINDOW CONTROL SYSTEM (POWER WINDOW REGULATOR MOTOR (for DRIVER AND PASSENGER SIDE DOORS)) |
Initialization procedures when replacing the power window regulator motor with new one.
Connect the battery and turn the ignition switch to ON. At this time, the LED on the power window switch blinks to indicate that it is ready for initialization.
Fully open the window by fully pushing the power window switch, and hold the switch for 1 second or more after the window is fully opened.
Fully close the power window by fully pulling the power window switch, and hold the switch for 1 second or more after the window is fully closed to reset the glass position. The LED on the power window switch changes from blinking to illuminated to indicate that the initialization is complete.
Initialization procedures when removing/installing the power window regulator motor or power window does not fully open.
Connect the battery and turn the ignition switch to ON.
Fully close the power window by fully pulling the power window switch, and hold the switch up for 6 seconds or more after the window is fully closed. If the power window does not move or stops halfway even when the switch is fully pulled, release the switch and fully pull it again.
Fully open the window by pushing down the power window switch, and hold the switch down for 1 second or more after the window is fully opened.
Release the power window switch. Then fully push and hold the switch 4 seconds or more.
Fully close the power window by fully pulling the power window switch, and hold the switch 1 second or more after the window is fully closed to reset the glass position the initialization is complete.
| INITIALIZE BACK DOOR POWER WINDOW CONTROL SYSTEM (BACK DOOR POWER WINDOW REGULATOR MOTOR) |
Push the DOWN switch (MANUAL DOWN or AUTO DOWN) to lower the back door power window until it is about one-quarter open.
Fully close the back door power window by pulling up the switch (AUTO UP) and then hold the switch up for an additional 1 second or more to reset the power window motor and complete the initialization.
If the back door power window opens after the held switch is released, then the reset failed. Repeat the reset procedure again.
| INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
Turn the ignition switch ON.
By pushing the SLIDE switch to close or the TILT switch to up on the roof console box, make the sliding roof operate as follows: TILT UP → approximately 1 second pause → TILT DOWN (The sliding roof lowers a little after it is fully tilted up.)
Check that the sliding roof stops at the fully closed position.
This completes the initialization.
Check that the AUTO operation works normally.
| RESET BACK DOOR CLOSE POSITION |
To initialize, close the back door completely by hand.