Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > INITIALIZATION



PROCEDURES NECESSARY WHEN CABLE IS DISCONNECTED/RECONNECTED TO BATTERY TERMINAL

Procedures necessary when cable is disconnected/reconnected to battery terminal 
Necessary Procedure
Procedure Details
Effect or Inoperative Function when Necessary Procedure is not Performed
Note
Power back door system initialization
To initialize, close the back door completely by hand.
Jam protection function
If the back door is closed when disconnecting the cable from the battery terminal, it is not necessary to reset it.

NOTICE:
w/ Navigation System:
After the ignition switch is turned off, the navigation receiver assembly requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

Procedures necessary when ECU or other parts are replaced 
Replacement Part
Necessary Procedures
Effect or Inoperative Function when Necessary Procedure is not Performed
Note
  1. Automatic transmission assembly
  2. Valve body assembly
  3. Shift solenoid valve
Reset memory
Large shift shock
-
Automatic transmission fluid
ATF thermal degradation estimate reset
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.
-
Suspension control ECU
Registration
Air suspension system
-
Skid control ECU
  1. Deceleration sensor zero point calibration
  2. Master cylinder pressure sensor zero point calibration
ABS warning and slip indicator light illumination
-
Yaw rate sensor
  1. Zero point calibration data clearance
  2. Deceleration sensor zero point calibration
  1. ABS warning and slip indicator light illumination
  2. VSC control is prohibited or operation is incorrect
-
Front Wheel Alignment Adjustment
  1. Zero point calibration data clearance
  2. Deceleration sensor zero point calibration
  3. Perform initialization of steering angle sensor
ABS warning and slip indicator light illumination
Complete the adjustment of the steering wheel and wheel alignment, and then initialize the steering angle sensor. If the order is reversed, the steering wheel and wheel alignment will become misaligned.
Occupant classification ECU
  1. Zero point calibration
  2. Sensitivity check
  1. Occupant classification system
  2. Passenger airbag ON/OFF indicator
  3. Airbag system (Front passenger side)
  4. Seat belt warning system (Front passenger side)
-
  1. Transponder key ECU
  2. ECM
  3. Key
Registration
Engine starting
Refer to the Service Bulletin for the registration procedure.
  1. Door control transmitter
  2. Door control receiver
Register recognition code
Wireless door lock operation
-
Inner rear view mirror
  1. Compass zone setting
  2. Compass calibration
  1. Direction is not displayed correctly
-
  1. Power window regulator motor (for Driver Side)
  2. Power window regulator motor (for Passenger Side)
Initialize the motor
  1. Jam protection function
  2. Power window control system
-
Back power window regulator motor
Initialize the motor
  1. Back power window control system
  2. Jam protection function
-
Sliding roof drive gear (Sliding roof ECU)
Initialize sliding roof system
  1. Auto operation
  2. Jam protection function
  3. Sliding roof operation after ignition switch is turned OFF
  4. Key-linked operation function (Driver side door only)
-
  1. Power back door unit
  2. Back door lock
Initialize power back door system
Power back door system
-

RESET MEMORY

NOTICE:
  1. Perform the Reset Memory (AT initialization) when replacing the automatic transmission assembly, valve body assembly or any of the shift solenoid valves.
  2. The Reset Memory can only be performed with the GTS.

HINT:
The ECM memorizes the control conditions of the automatic transmission assembly and engine assembly. Therefore, when the automatic transmission assembly, valve body assembly or any of the shift solenoid valves has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information.
Reset procedure is as follows.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.

    NOTICE:
    After performing the Reset Memory, be sure to perform the Road Test described earlier.

    HINT:
    The ECM learns through the Road Test.


ATF THERMAL DEGRADATION ESTIMATE RESET

NOTICE:
If either of the following conditions is met, perform ATF Thermal Degradation Estimate Reset.
  1. The ATF has been replaced.

HINT:
If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.

  1. Approximately 50% or more of the ATF has been replaced during a repair of the transmission or a similar operation.
  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  3. Turn the GTS on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility / ATF Thermal Degradation Estimate Reset.


REGISTRATION OF VEHICLE IDENTIFICATION INFORMATION
  1. Turn the ignition switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the intelligent tester on.

  5. Enter the following menus: Chassis / Air suspension / Utility / Signal Check.

  6. Check that the height control MAN. indicator light in the combination meter indicates that the system has entered Test Mode.

    HINT:
    1. When vehicle identification information is stored, the height control MAN. indicator light blinks in the Test Mode pattern (0.125 seconds on and 0.125 seconds off).
    2. When vehicle identification information is not stored, the height control MAN. indicator light blinks at 1 second intervals (1 second on and 1 second off).


CLEAR ZERO POINT CALIBRATION DATA (WHEN USING INTELLIGENT TESTER)
  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Select the skid control ECU to clear the zero point calibration date using the intelligent tester.
    Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Reset Memory.


PERFORM ZERO POINT CALIBRATION OF MASTER CYLINDER PRESSURE SENSOR AND DECELERATION SENSOR (WHEN USING INTELLIGENT TESTER)

NOTICE:
  1. While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it stationary. Do not start the engine.
  2. While obtaining the zero point, do not depress the brake and accelerator pedal.
  3. Obtain the zero point on a level surface (with an inclination of less than 1°).

  1. Enter Test Mode.

    1. Turn the ignition switch off.

    2. Check that the shift lever is in P or N and apply the parking brake.

      CAUTION:
      Application of the parking brake is not necessary for entering test mode. However, apply the parking brake for safety.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    5. Turn the intelligent tester on.

    6. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Test Mode.

  2. Obtain the zero points of the master cylinder pressure sensor and deceleration sensor.

    1. Keep the vehicle stationary on a level surface for 1 second or more.

      HINT:
      1. The zero point calibration is performed only once after the system enters test mode.
      2. Calibration cannot be performed again until the stored data is cleared once.

    2. Check that DTC C1336 is cleared.

    3. Turn the ignition switch off.


CLEAR ZERO POINT CALIBRATION DATA (WHEN USING SST CHECK WIRE)
  1. Turn the ignition switch to ON.



  2. F100115E85
  3. Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.

    SST
    09843-18040  

  4. Check that the slip indicator light comes on.

  5. Using a check wire, perform the zero point calibration of the deceleration sensor.


PERFORM ZERO POINT CALIBRATION OF MASTER CYLINDER PRESSURE SENSOR AND DECELERATION SENSOR (WHEN USING SST CHECK WIRE)

NOTICE:
  1. While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it stationary. Do not start the engine.
  2. While obtaining the zero point, do not depress the brake pedal.
  3. Obtain the zero point on a level surface (with an inclination of less than 1°).



  1. Enter Test Mode.

    1. Turn the ignition switch off.

    2. Check that the shift lever is in P or N and apply the parking brake.

      CAUTION:
      Application of the parking brake is not necessary for entering test mode. However, apply the parking brake for safety.



    3. F100115E85
    4. Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

      SST
      09843-18040  

    5. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

  2. Obtain the zero points of the master cylinder pressure sensor and deceleration sensor.

    1. Keep the vehicle stationary on a level surface for 1 second or more.

      HINT:
      1. The zero point calibration is performed only once after the system enters test mode.
      2. Calibration cannot be performed again until the stored data is cleared once.

    2. Check that DTC C1336 is cleared.

    3. Turn the ignition switch off.


PERFORM INITIALIZATION OF STEERING ANGLE SENSOR

NOTICE:
Complete the adjustment of the steering wheel and wheel alignment, and then initialize the steering angle sensor. If the order is reversed, the steering wheel and wheel alignment will become misaligned.

  1. Check that the steering wheel is in the centered position.

  2. Disconnect the negative (-) battery terminal for more than 2 seconds.

    NOTICE:
    After the ignition switch is turned off, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch off, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

  3. Reconnect the negative (-) battery terminal.


ZERO POINT CALIBRATION
  1. Zero point calibration procedures:

    HINT:
    Make sure that the zero point calibration has finished normally, and then perform the sensitivity check.


    1. Check that all of the following conditions are met:

      1. The vehicle is parked on a level surface.
      2. No objects are placed on the front passenger seat.
      3. The front seat inner belt RH (passenger side buckle switch) is off.

    2. Adjust the seat position in accordance with the table below.
      Adjustment Item
      Position
      Slide Direction
      Rearmost position
      Reclining Angle
      Upright position
      Headrest Height
      Lowest position
      Lifter Height
      Lowest position

    3. Turn the ignition switch off.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch ON and turn the intelligent tester on.

    6. Enter the following menus: Body / Occupant Detection / Utility / Zero Point Calibration.

    7. Perform the zero point calibration by following the prompts on the intelligent tester screen.

      HINT:
      1. Refer to the intelligent tester operator's manual for further details.
      2. If the zero point calibration has not finished normally, replace the front seat RH.

      OK:
      "Zero Point calibration is complete." is displayed.


SENSITIVITY CHECK
  1. Sensitivity check procedures:

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch ON and turn the intelligent tester on.

    4. Enter the following menus: Body / Occupant Detection / Utility / Sensitivity Check.

    5. Perform the sensitivity check by following the prompts on the intelligent tester screen.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    6. Confirm that the beginning sensor reading is within the standard range.

      Standard range:
      -3.2 to 3.2 kg (-7.0 to 7.0 lb)

    7. Place a 30 kg (66.2 lb) weight (e.g. a lead mass) onto the front passenger seat.

    8. Confirm that the sensitivity is within the standard range.

      Standard range:
      27 to 33 kg (59.5 to 72.8 lb)

      HINT:
      1. When performing the sensitivity check, use a solid metal weight (the check result may not be accurate if a liquid weight is used).
      2. If the sensitivity deviates from the standard range, retighten the bolts of the front passenger seat taking care not to deform the seat rail. After performing this procedure, if the sensitivity is not within the standard range, replace the front passenger seat.


DESCRIPTION OF CODE REGISTRATION

HINT:
  1. Recognition code registration is necessary when replacing the door control transmitter or the door control receiver.
  2. Add mode is used to retain the already registered codes while registering a new recognition code. This mode is used when adding a transmitter. If the number of registered codes exceeds 6, the previously registered code will be correspondingly cleared in order, starting from the code registered first.
  3. Rewrite mode is used to clear all the previously registered codes and register only new recognition codes. This mode is used when exchanging the transmitter or the door control receiver for new one.
  4. Confirmation mode is used to confirm how many recognition codes have already been registered before an additional registration of a recognition code.
  5. Prohibition mode is used to clear all the registered codes and cancel the wireless door lock function. Use this mode when the transmitter is lost.
  6. All the following registration procedures must be performed in order continuously.


REGISTER RECOGNITION CODE (USING OR INTELLIGENT TESTER)

HINT:
For detailed procedures, refer to the prompts on the intelligent tester screen. The number of currently registered codes can be checked out on the first screen of the Wireless Registration.

  1. Turn the ignition switch ON.

  2. Enter the following menus: Body / Main Body / Wireless Registration.

  3. Press both LOCK and UNLOCK switches between 1 to 1.5 seconds.

  4. Press either switch for more than 1 second within 3 seconds.



  5. Check the response to the registration completion.


    B111915E15

    HINT:
    1. If the LOCK-UNLOCK operation occurs twice, the registration of the recognition code has failed. Perform the registration procedures again from the beginning.
    2. If registering another transmitter, repeat the procedures after the intelligent tester operation. All 4 recognition codes can be registered consecutively.

  6. Perform either of the following to complete the registration of recognition codes:

    1. Use the intelligent tester to send completion command.
    2. Disconnect the intelligent tester.


REGISTER RECOGNITION CODE (USING SWITCH OPERATION)
  1. The following conditions must be met.

    1. No key in the ignition key cylinder.
    2. The driver side door is open (the other doors are closed).
    3. The driver side door is unlocked.

  2. Insert and remove the key into / from the ignition key cylinder twice (Insert → Remove → Insert → Remove) within 5 seconds.

    HINT:
    The procedure should end with the key removed.

  3. Perform the following operations within 40 seconds.

    1. Close and open the driver side door twice (Close → Open → Close → Open).

      HINT:
      The procedure should end with the door open.

    2. Insert and remove the key into / from the ignition key cylinder (Insert → Remove).

      HINT:
      The procedure should end with the key removed.

    3. Close and open the driver side door twice (Close → Open → Close → Open).

      HINT:
      The procedure should end with the door open.

    4. Insert the key into the ignition key cylinder and close all doors.



  4. Perform the following operations within 40 seconds.



    1. Turn the ignition switch from ON to OFF at approximately 1 second intervals. Operate the ignition switch according to the number of times shown below.


      B111914E11

      HINT:
      If the number of ignition switch ON - OFF operations is 0, 4, 6 or more, there will be no response (the power door lock and unlock operation) to show which mode has been selected.

    2. Remove the key from the ignition key cylinder.



  5. Check the response of the selected mode within 5 seconds.


    B111913E11

    NOTICE:
    After the system has been set to the prohibition mode, enter the confirmation mode and check that the number of registered keys is 0.

    HINT:
    1. In the confirmation mode, LOCK-UNLOCK operation will occur once for each recognition code that has been registered. For example, if 2 recognition codes have been registered, LOCK-UNLOCK operation will occur twice.
    2. In the confirmation mode, if no recognition codes have been registered, LOCK-UNLOCK operation will occur 5 times.
    3. If confirmation mode or prohibition mode is selected, the operation ends after the response to the selected mode completes.

  6. Within 40 seconds of completing the confirmation mode operation, press the LOCK and UNLOCK switches on the transmitter simultaneously.

  7. After completing the above step, press a shingle switch (LOCK or UNLOCK) within 5 seconds.



  8. After completing the above step, check the response to the registration completion within 3 seconds.


    B111915E16

    HINT:
    1. If the LOCK-UNLOCK operation occurs twice, the registration of recognition code has failed. Perform registration procedures again from the beginning.
    2. If registering another transmitter, repeat the procedures after the response to the selected mode confirmation. All 6 recognition codes can be registered consecutively.

  9. Perform either of the following to complete the registration of recognition codes:

    1. Open the door.
    2. Insert the key into the ignition key cylinder.


SELECT COMPASS DISPLAY MODE
  1. The compass switch allows you to select the Display or Non-display mode of the compass.


SET ZONE
  1. Deviation between the "magnetic north" and "actual north" differs depending on the location. Therefore, adjustment of the magnetism is required. Because the magnetic condition differs depending on the area where the vehicle is used, it is necessary for each user to set the zone (refer to Compass Zone Map). The zone setting can be changed using the compass switch of the inner mirror.


PERFORM CALIBRATION
  1. Because each vehicle has its own magnetic field, calibration should be performed for each individual vehicle. This compass function is used when storing the record of the vehicle's magnetic field.


WHEN COMPASS IS MAGNETIZED
  1. The compass could be magnetized during shipping by vessels or freight cars. Therefore, ensure that calibration is performed properly before delivery. If driving the vehicle in a circle several times does not complete the calibration procedure, there may be a compass magnetization problem.


B251093E01


Deviation Calibration Procedure
B219621
  1. Turn the ignition switch to the "IG-ON" position and push and hold the "AUTO" switch for 6 seconds until the zone number appears on the display.

    HINT:
    Pushing the "AUTO" switch for 3 seconds turns on or off the compass display.



  2. Push the "AUTO" switch to select the number of the zone where the vehicle is located.
    See the map for zone reference.


    B231508E02


Circling Calibration Procedure
B141149
  1. Start the engine and push and hold the "AUTO" switch for 9 seconds until "C" appears on the display.



  2. C180413
  3. Drive the vehicle slowly at 8 km/h (5 mph) or lower in a circle.
    If there is not enough space to drive in a circle, turn the car around in the following manner, doing two three-point turns in succession.
    After driving in 1 to 3 circles in the above method, calibration is completed with the direction is shown on the display.

    HINT:
    1. Do not perform calibration of the compass in a place where the earth's magnetic field is subject to interference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).
    2. During calibration, do not operate electric systems (sliding roof, power windows, etc.) as they may interfere with the calibration.


INITIALIZATION PROCEDURE

NOTICE:
If the fold seat control ECU is replaced, the seat position becomes unstable and the power seat motor must be reset (pulse sensor position must be initialized). If reset is not performed, stowage operation, return operation, and jam protection do not function.

HINT:
  1. Perform the initialization procedure after confirming that a seat position is not recorded in the fold seat control ECU (ECU is not initialized).
  2. If initialization has been completed, repeat initialization cannot be performed. If repeat initialization is necessary, perform the initialization release procedure before initialization.

  1. Press the rear power seat switch in the forward position until the third-row seat is completely folded (stowed).

  2. With the third-row seat in the completely folded position (stored), hold the rear power seat switch in the forward position for 1 more second.

  3. The buzzer sounds twice when the initialization is complete.


INITIALIZATION RELEASE PROCEDURE

HINT:
  1. Perform the initialization release procedure after confirming that a seat position is recorded in the fold seat control ECU (ECU is initialized).
  2. Perform initialization release when the initialization needs to be cleared, such as when the fold seat control ECU (computer where the seat position is recorded) has been swapped left-to-right or with one from another vehicle for troubleshooting.

  1. While holding the fold seat switch in the return position, press the rear power seat switch in the forward position 5 times before 10 seconds elapse. This will complete the initialization release procedure.

    NOTICE:
    1. If the fold seat switch is not held in the return position for more than 10 seconds, the initialization release will be cancelled.
    2. If the rear power seat switch is pressed 6 times before 10 seconds have elapsed with the fold seat switch held in the return position, the initialization release will be cancelled.


INITIALIZE POWER WINDOW CONTROL SYSTEM (POWER WINDOW REGULATOR MOTOR (for DRIVER AND PASSENGER SIDE DOORS))

NOTICE:
When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized. Functions such as the AUTO UP/DOWN, jam protection and key-off do not operate if the initialization is not performed.

HINT:
When the battery is replaced, it is not necessary to initialize the power window regulator motor.

NOTICE:
  1. When performing initialization, do not perform any other procedures.
  2. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used, due to detection of the different operation learned value of the door glass movement speed. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
    (a) Open the power window by fully pushing down the power window switch.
    (b) Close the power window by fully pulling up the power window switch and holding it at the AUTO UP position.
  3. If the initialization is not completed properly, the LIN communication system may have a malfunction.

  1. Initialization procedures when replacing the power window regulator motor with new one.

    1. Connect the battery and turn the ignition switch to ON. At this time, the LED on the power window switch blinks to indicate that it is ready for initialization.

    2. Fully open the window by fully pushing the power window switch, and hold the switch for 1 second or more after the window is fully opened.

    3. Fully close the power window by fully pulling the power window switch, and hold the switch for 1 second or more after the window is fully closed to reset the glass position. The LED on the power window switch changes from blinking to illuminated to indicate that the initialization is complete.

  2. Initialization procedures when removing/installing the power window regulator motor or power window does not fully open.

    1. Connect the battery and turn the ignition switch to ON.

    2. Fully close the power window by fully pulling the power window switch, and hold the switch up for 6 seconds or more after the window is fully closed. If the power window does not move or stops halfway even when the switch is fully pulled, release the switch and fully pull it again.

    3. Fully open the window by pushing down the power window switch, and hold the switch down for 1 second or more after the window is fully opened.

    4. Release the power window switch. Then fully push and hold the switch 4 seconds or more.

    5. Fully close the power window by fully pulling the power window switch, and hold the switch 1 second or more after the window is fully closed to reset the glass position the initialization is complete.


INITIALIZE BACK DOOR POWER WINDOW CONTROL SYSTEM (BACK DOOR POWER WINDOW REGULATOR MOTOR)

NOTICE:
The back door power window motor must be reset (pulse sensor initialized) the following.

  1. Push the DOWN switch (MANUAL DOWN or AUTO DOWN) to lower the back door power window until it is about one-quarter open.

    HINT:
    Skip this step if the back door window has already been lowered to this position.

  2. Fully close the back door power window by pulling up the switch (AUTO UP) and then hold the switch up for an additional 1 second or more to reset the power window motor and complete the initialization.

  3. If the back door power window opens after the held switch is released, then the reset failed. Repeat the reset procedure again.

    NOTICE:
    If the switch is operated for too long, the back door power window may be deactivated by the Positive Temperature Coefficient (PTC) resistor, and continued use of the switch may temporarily deactivate AUTO operation. In these cases, wait a while and perform the reset operation again.


INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NOTICE:
When replacing the sliding roof drive gear, the new sliding roof drive gear requires initialization. If a reset is not executed, the following functions do not operate: AUTO operation and jam protection function.

  1. Turn the ignition switch ON.

  2. By pushing the SLIDE switch to close or the TILT switch to up on the roof console box, make the sliding roof operate as follows: TILT UP → approximately 1 second pause → TILT DOWN (The sliding roof lowers a little after it is fully tilted up.)

  3. Check that the sliding roof stops at the fully closed position.

  4. This completes the initialization.

  5. Check that the AUTO operation works normally.

    NOTICE:
    If the following conditions occur while operating, initialization will fail.
    1. Ignition switch is turned OFF.
    2. Pushed sliding roof switch is released while sliding roof is operating.

    HINT:
    1. If the sliding roof cannot fully close or its position has become misaligned, perform the initialization again.
    2. If the sliding roof TILT switch to up or SLIDE switch to close is pressed and held until the roof glass has either stopped moving or started moving in the opposite direction, and then the switch is held for another 10 seconds or more, perform the initialization again.
    3. If the AUTO operation function and jam protection function do not operate after the drive gear has been initialized, replace the sliding roof drive gear (sliding roof ECU).


RESET BACK DOOR CLOSE POSITION
  1. To initialize, close the back door completely by hand.

    HINT:
    If the back door is closed when disconnecting the cable from the battery terminal, it is not necessary to reset it.