Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > CUSTOMIZE PARAMETERS


HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.


CUSTOMIZING FUNCTION WITH INTELLIGENT TESTER
  1. POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

    Tilt & Telescopic 
    Display (Item)
    Default
    Content
    Setting
    Autoaway/Return function
    ON
    ON/OFF of the auto away/return function
    ON/OFF

  2. POWER DOOR LOCK CONTROL SYSTEM

    Door Lock 
    Display (Item)
    Default
    Content
    Setting
    Auto lock
    ON
    Function that locks all doors and fuel lid when vehicle speed reaches a certain level.
    ON/OFF
    Auto Lock/Shift
    OFF
    Function that locks all doors and fuel lid when shift lever is moved to any other position from P with engine running and all doors closed.
    ON/OFF
    Auto Unlock/Shift
    ON
    Function that unlocks all doors and fuel lid when shift lever is moved to P from any other position while the ignition switch to ON.
    ON/OFF
    All Unlock/Open-Close
    OFF
    Function that unlocks all doors and fuel lid when opening driver door within 10 seconds after turning the ignition switch to ON.
    ON/OFF

  3. WIRELESS DOOR LOCK CONTROL SYSTEM

    Wireless Door Lock 
    Display (Item)
    Default
    Content
    Setting
    Wireless Control
    ON
    ON/OFF of wireless door lock function
    ON/OFF
    Hazard Answer Back
    ON
    When LOCK switch on transmitter pressed, all hazard warning lights illuminate once. When UNLOCK switch pressed, all hazard warning lights illuminate twice.
    ON/OFF
    Wireless Buzzer Resp
    ON
    Function that makes wireless buzzer sound for answer-back when transmitter LOCK / UNLOCK switch is pressed.
    ON/OFF
    Open Door Warning
    ON
    If door is not completely closed and transmitter LOCK switch is pressed, this function sounds a buzzer for 10 seconds.
    ON/OFF
    Panic Function
    ON
    This function operates the theft deterrent system when PANIC is pressed and held for 0.8 second or more.
    ON/OFF
    Auto Lock Time
    30s
    This function controls amount of time from unlocking doors to automatic re-locking function.
    30s/60s/120s

  4. THEFT DETERRENT SYSTEM

    Security 
    Display (Item)
    Default
    Content
    Setting
    Warning by Horn
    ON
    Function that allows the vehicle horn and theft deterrent horn to be used as warning devices
    ON/OFF

  5. LIGHTING SYSTEM (INTERIOR)

    Illuminated Entry 
    Display
    Default
    Content
    Setting
    Lighting Time
    15s
    Changes illumination duration after door closure
    (It will quickly fade out when turning ignition switch ON)
    7.5s/15s/30s
    I/L when ACC OFF
    ON
    Illuminates light when ignition switch turned to ACC → OFF
    (Room light illuminated when interior light switch set to DOOR)
    ON/OFF
    I/L ON W/Door Key Unlock
    ON
    Function to light up room light when unlocking with door key cylinder
    (Room light illuminated when interior light switch set to DOOR)
    ON/OFF

    Light Control 
    Display
    Default
    Content
    Setting
    Disp Ex ON Sen
    Normal
    Changes brightness when lowering lights such as combination meter indicator light, A/C indicator light, and clock light*2
    Light2/Light1/Normal/Dark1/Dark2
    Disp Ex OFF Sen
    Normal
    Changes brightness when canceling lowering lights such as combination meter indicator light, A/C indicator light, and clock light*3
    Light2/Light1/Normal/Dark1/Dark2
    Sensitivity
    Normal
    Function to adjust sensitivity of lighting illumination*1
    Light2/Light1/Normal/Dark1/Dark2

    HINT:
    *1: The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


    *1 
    Lighting brightness

    E107164

    Setting
    Dark2
    Dark1
    Normal
    Light1
    Light2

    *2 
    Brightness when lowering the lights

    E107164

    Setting
    Dark2
    Dark1
    Normal
    Light1
    Light2

    *3 
    Brightness when canceling the lowering of the lights

    E107164

    Setting
    Dark2
    Dark1
    Normal
    Light1
    Light2

  6. METER / GAUGE SYSTEM

    Warning 
    Display (Item)
    Default
    Content
    Setting
    Key Remind Volume
    Large
    To change volume of key reminder buzzer
    Large/Small/Medium
    Key Remind Sound
    Slow
    To change frequency of key reminder buzzer
    Normal/Slow/Fast
    Driver Side Seatbelt Warning Buzzer
    ON
    To change setting of driver side seat belt warning buzzer
    ON/OFF
    Front Passenger Side Seatbelt Warning Buzzer
    ON
    To change setting of passenger side seat belt warning buzzer
    ON/OFF

  7. SEAT BELT WARNING SYSTEM

    Warning 
    Display (Item)
    Default
    Content
    Setting
    Driver Side Seatbelt Warning Buzzer
    ON
    Seat belt warning buzzer ON/OFF setting
    ON: Driver buzzer on
    OFF: Driver buzzer off
    Front Passenger Side Seatbelt Warning Buzzer
    ON
    Seat belt warning buzzer ON/OFF setting
    ON: Passenger buzzer on
    OFF: Passenger buzzer off

    HINT:
    When the buzzer off setting is selected, the buzzer activation while the vehicle is being driven is cancelled. However, the buzzer activation when the ignition switch is turned to ON cannot be cancelled.

  8. AIR CONDITIONING SYSTEM

    Air Conditioner 
    Display
    Default
    Content
    Setting
    Set Temperature Shift
    Normal
    Function to control the shifted temperature in relation to the displayed temperature
    +2 C/+1 C/Normal/-1 C/-2 C
    Compressor Mode
    Automatic
    Function to turn the A/C ON automatically by pressing the AUTO button when the blower is ON and the A/C is OFF
    Manual/Automatic
    Foot/DEF Auto Mode
    ON
    Function to turn the airflow from FOOT/DEF ON automatically when AUTO MODE is ON
    ON/OFF
    Foot/DEF Automatic Blow Up Function
    ON
    Function to change the blower level automatically when the defroster is ON
    ON/OFF
    Ambient Temperature Shift
    Normal
    Function to control the shifted ambient temperature in relation to the displayed ambient temperature
    +3 C/+2 C/+1 C/Normal/-1 C/-2 C/-3 C

  9. POWER WINDOW CONTROL SYSTEM

    Power Window 
    Display (Item)
    Default
    Content
    Setting
    Door Key P/W Up
    ON
    Function that raises the driver and passenger power windows when, with the ignition switch off, a key is used to hold the driver door key cylinder to the lock position for more than 2.3 seconds.
    ON/OFF
    Door Key P/W Down
    ON
    Function that lowers the driver and passenger power windows when, with the ignition switch off, a key is used to hold the driver door key cylinder to the unlock position for more than 2.3 seconds.
    ON/OFF
    Door Key Linked Back P/W UP
    AVAIL
    Function that raises the back door power window when, a key is used to hold the back door key cylinder to the lock position for more than 0.7 seconds.
    NOT AVL/AVAIL
    Door Key Linked Back P/W DOWN
    AVAIL
    Function that lowers the back door power windows when, a key is used to hold the back door key cylinder to the unlock position for more than 0.7 seconds.
    NOT AVL/AVAIL

  10. SLIDING ROOF SYSTEM

    Sliding Roof 
    Display (Item)
    Default
    Content
    Setting
    Door Key Related Operation
    Slide
    Function to select either tilt up or slide open for the manual sliding roof operation linked with power window, which is activated by holding the driver door key in the unlock position for 3 seconds or more when the ignition switch is off.
    Tilt/Slide
    Door Key Related Open
    ON
    Function to manually open the sliding roof linked with power window by holding the driver door key in the unlock position for 3 seconds or more when the ignition switch is off.
    ON/OFF
    Door Key Related Close
    ON
    Function to manually close the sliding roof linked with power window by holding the driver door key in the lock position for 3 seconds or more when ignition switch is off.
    ON/OFF

  11. POWER BACK DOOR SYSTEM

    Power Back Door System 
    Display (Item)
    Default
    Function
    Setting
    PBD SW Operation
    0.8 s
    Function that turns power back door closer switch on when switch is pushed once or held down for 0.8 sec.
    0.8 s / ON
    PBD Buzzer*
    ON
    This function makes the power back door buzzer sound when power back door is operating
    ON / OFF
    Wirels PBD SW Operation
    0.8 s
    Function that operates power back door when transmitter switch is pressed in specified way
    1 Oper / 2 Oper / 0.8 s / OFF / 1 Motion

    HINT:
    *: The warning buzzer that sounds when the power back door is operating cannot be customized. (Even if this function is set to "OFF", the buzzer will still sound.)

  12. WIPER AND WASHER SYSTEM

    Wiper 
    Display
    Default
    Content
    Setting
    Linked Rear Wiper Washer
    AVAIL
    Function to make the rear wiper run automatically after the washer function is used.
    NOT AVAIL/AVAIL
    Rewipe Function
    AVAIL
    Function to make the rear wiper run once automatically a certain amount of time after the washer function is completed, to prevent the dripping of washing fluid.
    NOT AVAIL/AVAIL

  13. LIGHTING SYSTEM (EXTERIOR)

    Light Control 
    Display
    Default
    Content
    Setting
    Sensitivity
    Normal
    Function to adjust sensitivity of lighting illumination*1
    Light2/Light1/Normal/Dark1/Dark2

    HINT:
    *1: The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


    *1 
    Lighting brightness

    E107164

    Setting
    Dark2
    Dark1
    Normal
    Light1
    Light2

    Mirror ECU 
    Display
    Default
    Content
    Setting
    Foot Light
    15s
    Changes illumination duration after door closure
    OFF/7.5s/15s/30s


CUSTOMIZING FUNCTION WITH MULTI-INFORMATION DISPLAY (w/ Multi-information Display)


  1. Using the SETUP switch and SELECT switch, the following functions can be customized through the multi-information display. Refer to the illustration below.

    1. Unit setting
    2. Wireless door lock control system (answer-back function, automatic lock function, 2-step unlock function)
    3. Power door lock control system (automatic door lock function, automatic door unlock function)
    4. Lighting system (auto light turn off function)
    5. Default setting (customize setting cancel function)

    E183917E01


    E183918E01


    E183919E01

    HINT:
    *: When setting change operation is performed by SELECT switch, writing of customized value must be performed.