Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM

TOYOTA PARKING ASSIST-SENSOR SYSTEM > OPERATION CHECK

for Preparation Click here



CHECK INITIAL CHECK FUNCTION
E303034E01
  1. Check the initial check function for the LED.

    1. When the clearance sonar main switch is turned ON, check that the following occurs: 1) after 0.4 seconds, the LEDs are turned on for approximately 0.7 to 1.3 seconds, and 2) the system starts the obstacle detection operation.

  2. Check the initial check function for the sensor.

    1. Approximately 0.4 seconds after the ignition switch has been turned to ON and the clearance sonar main switch has been turned ON, all sensors will be checked by the system.
    2. After 0.7 to 1.3 seconds have elapsed, the check operation for all of the sensors will stop when a vehicle speed of over 10 km/h (6 mph) is detected.
    3. When the vehicle has been shifted from P, the system will change to obstacle detection operation according to the shift lever position.
    4. If there are no changes in the conditions, such as those listed above (speed or shift lever position), the sensor check operation will be halted after 5 +/-1 second have elapsed. If one or more sensors are anomalous, check operation for all of the sensors will continue (sensors will continue transmitting).



  3. If the sensor is found to have an anomaly due to an open circuit or freezing for approximately 5 seconds or more, indications as shown in the following illustration appear.



    1. When the ECU judges that the sensor needs to be repaired:


      E303037E01



    2. When the ECU judges that the sensor needs to be cleaned:


      E303038E01

      HINT:
      If the clearance sonar main switch is ON and the ignition switch is turned to ON, the buzzer does not sound.


DETECTION RANGE MEASUREMENT AND INDICATOR CHECK

NOTICE:
Apply the parking brake securely so that the vehicle does not move.

  1. Turn the ignition switch to ON.

  2. Move the shift lever to R to check the front corner sensors, rear corner sensors and back sensors.

  3. Move the shift lever to D, S or N to check the front corner sensors.

  4. Turn the clearance sonar main switch ON.



  5. Move a pole around the sensor to measure the detection range of the sensor.

    NOTICE:
    1. These detection ranges are applicable when positioning the pole parallel or perpendicular to the ground.
    2. The ranges vary depending on the measuring method and type of obstacle (such as walls).
    3. For close-range, medium-range and long-range detection, the values shown are for when using a pole with a diameter of 60 mm (2.36 in.). For longest-range detection, the values shown are for when using a pole with a diameter of 400 mm (15.7 in.).




    1. Front corner sensors detection range


      E300425E01

      HINT:
      *1: The No. 2 ultrasonic sensor side view detection ranges hatched area represents the cross section of the top view detection range A lines. The hatched area does not represent the entire side view detection range.



    2. Rear corner sensors detection range


      E300426E01



    3. Back sensors detection range


      E300427E01

      HINT:
      *1: The No. 2 ultrasonic sensor side view detection ranges hatched area represents the cross section of the top view detection range A lines. The hatched area does not represent the entire side view detection range.



  6. When the ultrasonic sensors have detected an obstacle, check the accessory meter and buzzer sounds with the clearance sonar main switch ON.

    Operation Condition 
    Shift Lever Position
    Vehicle Speed
    Buzzer Detection, Accessory Meter Detection
    Front Corner LH
    Front Corner RH
    Back LH
    Back RH
    Rear Corner LH
    Rear Corner RH
    P
    -
    X
    X
    X
    D, S, (N)
    10 km/h (6.2 mph) or less
    ○
    X
    X
    R
    No Limit
    ○
    ○
    ○



    1. Check the buzzer sounds with the clearance sonar main switch ON.


      E270549E02


      Front Corner Detection Range 
      Detection
      Distance
      1. Close-range detection
      Within 300 +/- 30 mm (11.8 +/- 1.18 in.)
      2. Medium-range detection
      300 +/- 30 to 450 +/- 50 mm (11.8 +/- 1.18 to 17.7 +/- 1.97 in.)
      3. Long-range detection
      450 +/- 50 to 600 +/- 60 mm (17.7 +/- 1.97 to 23.6 +/- 2.36 in.)

      Rear Corner Detection Range 
      Detection
      Distance
      1. Close-range detection
      Within 400 +/- 40 mm (15.7 +/- 1.57 in.)
      2. Medium-range detection
      400 +/- 40 to 600 +/- 60 mm (15.7 +/- 1.57 to 23.6 +/- 2.36 in.)
      3. Long-range detection
      600 +/- 60 to 850 +/- 90 mm (23.6 +/- 2.36 to 33.5 +/- 3.54 in.)

      Back Detection Range 
      Detection
      Distance
      1. Close-range detection
      Within 500 +/- 50 mm (19.7 +/- 1.97 in.)
      2. Medium-range detection
      500 +/- 50 to 750 +/- 80 mm (19.7 +/- 1.97 to 29.5 +/- 3.15 in.)
      3. Long-range detection
      750 +/- 80 to 1000 +/- 100 mm (29.5 +/- 3.15 to 39.4 +/- 3.94 in.)
      4. Longest-range detection (to wall)
      1000 +/- 100 to 1800 +/- 180 mm (39.4 +/- 3.94 to 70.9 +/- 7.09 in.)

      HINT:
      Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.



    2. Check the indicator and buzzer on the accessory meter when the front corner sensors have detected an obstacle.

      Operation Condition 
      Ignition Switch
      Clearance Sonar Main Switch
      Shift Lever Position
      Vehicle Speed
      ON
      ON
      D, S, N
      10 km/h (6.2 mph) or less


      E146241E01


      Accessory Meter 
      Detection Range
      Buzzer
      Indicator Displayed
      1. Close-range detection
      Sounds continuously
      Corner indicator(s) are illuminated
      2. Medium-range detection
      Sounds intermittently
      (ON: 75 msec. / OFF: 75 msec.)
      Corner indicator(s) are blinking
      3. Long-range detection
      Sounds intermittently
      (ON: 150 msec. / OFF: 150 msec.)
      Corner indicator(s) are blinking

      HINT:
      Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.



    3. Check the accessory meter and buzzer when the front corner sensors, back sensors and rear corner sensors have detected an obstacle.

      Operation Condition 
      Ignition Switch
      Clearance Sonar Main Switch
      Shift Lever Position
      ON
      ON
      R position


      E146241E02


      Accessory Meter 
      Detection Range
      Buzzer
      Indicator Displayed
      1. Close-range detection
      Sounds continuously
      Corner indicator(s) are illuminated and/or back indicator is illuminated
      2. Medium-range detection
      Sounds intermittently
      (ON: 75 msec. / OFF: 75 msec.)
      Corner indicator(s) are blinking and/or back indicator is blinking
      3. Long-range detection
      Sounds intermittently
      (ON: 150 msec. / OFF: 150 msec.)
      Corner indicator(s) are blinking and/or back indicator is blinking
      4. Longest-range detection
      Sounds intermittently
      (ON: 150 msec. / OFF: 650 msec.)
      Back indicator is blinking

      HINT:
      Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.