Home › Drivetrain · AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0717    Turbine Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input revolution of the transmission. By comparing the input turbine speed signal NT with the counter gear speed sensor signal SP2, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, and as a result, the gears shift smoothly.

C162353E02


DTC Code
DTC Detection Condition
Trouble Area
P0717
All conditions below are detected for 5 seconds or more (1 trip detection logic)
(a) Gear change is not performed
(b) Gear position: 4th, 5th or 6th
(c) T/M input shaft rpm: 300 rpm or less
(d) T/M output shaft rpm: 1000 rpm or more
(e) Park/neutral position switch:
  1. NSW input signal is OFF
  2. R input signal is OFF
(f) Shift solenoid valves and park/neutral position switch are operating normally
  1. Open or short in speed sensor NT circuit
  2. Speed sensor NT
  3. ECM
  4. Automatic transmission (clutch, brake or gear, etc.)
Inspect using an oscilloscope:
Check the waveform of the ECM connector.
C162170E04

Standard:
Refer to the illustration.

Item
Content
Terminal No. (Symbol)
D56-124 (NT+) - D56-123 (NT-)
Tool setting
1 V/DIV., 2 msec./DIV.
Condition
Engine is idling (Shift lever in P or N)

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NT (turbine (input) speed sensor) or is output only a little. The NT terminal of the ECM detects the pulse signal from the speed sensor NT (input RPM). The ECM outputs a gear shift signal comparing the input speed sensor NT with the output speed sensor SP2.
While the vehicle is operating in the 4th, 5th or 6th gear position with the shift lever in D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is more than 1000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.

HINT:
  1. *1: Pulse is not output or is irregularly output.
  2. *2: The vehicle speed is approximately 50 km/h (30 mph) or more.


WIRING DIAGRAM


C155187E27


INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the intelligent tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    Lock-up is:
    1. ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
    2. OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm

    HINT:
    1. SPD (NT) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (30 mph) or more:
      Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT SPEED SENSOR NT INSTALLATION


    C159067E06
  1. Check the speed sensor NT installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR NT
OK


2.INSPECT SPEED SENSOR NT


    C159420E11
  1. Disconnect the D43 speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω



NG
REPLACE SPEED SENSOR NT (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)


    C159422E87
  1. Disconnect the D56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D56-124 (NT+) - D56-123 (NT-)
    20°C (68°F)
    560 to 680 Ω
    D56-124 (NT+) - Body ground
    Always
    10 kΩ or higher
    D56-123 (NT-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)