DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0705 | When one of following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic)
|
|

| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | Shift lever is:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (P Range) | PNP switch status/ ON or OFF | Shift lever is:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF | Shift lever is:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (N Range) | PNP switch status/ ON or OFF | Shift lever is:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Sports Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sports Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| Sports Mode Selection SW | Sport mode select switch status/ ON or OFF | Shift lever position is:
| - |
| Shift SW Status (D Range) | PNP switch status/ ON or OFF | Shift lever is:
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| 1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the D21 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift lever in P | Below 1 Ω |
| 2 (RB) - 1 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever in N | Below 1 Ω |
| 2 (RB) - 7 (DL) |
| Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher |
| 2 (RB) - 1 (RL) | Shift lever not in R | 10 kΩ or higher |
| Shift lever not in N | 10 kΩ or higher |
| 2 (RB) - 7 (DL) |
| 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT TRANSMISSION CONTROL SWITCH |
![]() |
Disconnect the H31 transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (IG) - 7 (S) | Shift lever in S, "+" and "-" | Below 1 Ω |
| 3 (IG) - 7 (S) | Shift lever not in S, "+" and "-" | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the D21 park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D21-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| D21-2 (RB) - Body ground | Ignition switch off | Below 1 V |
|
| ||||
| OK | |
| 4.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE) |
![]() |
Disconnect the H31 transmission control switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H31-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| H31-3 (IG) - Body ground | Ignition switch off | Below 1 V |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the D56 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|
| 11 to 14 V |
| D56-26 (R) - Body ground |
| 11 to 14 V* |
|
| 11 to 14 V |
| D56-27 (D) - Body ground |
| 11 to 14 V |
|
| Below 1 V |
| D56-26 (R) - Body ground |
| Below 1 V |
|
| Below 1 V |
| D56-27 (D) - Body ground |
| Below 1 V |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM) |
![]() |
Disconnect the A27 ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A27-25 (S) - Body ground | Shift lever in S, "+" and "-" | 11 to 14 V |
| A27-25 (S) - Body ground | Shift lever not in S, "+" and "-" | Below 1 V |
|
| ||||
| OK | ||
| ||