Home › Drivetrain · AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0712    Transmission Fluid Temperature Sensor "A" Circuit Low Input

DTC    P0713    Transmission Fluid Temperature Sensor "A" Circuit High Input

for Preparation Click here


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the ATF temperature into a resistance value which is input into the ECM.

C146747E03

The ECM applies a voltage to the temperature sensor through ECM terminal THO1.
The sensor resistance changes with the ATF temperature.
One terminal of the sensor is grounded so that the sensor resistance and voltage decrease as the temperature becomes higher.
The ECM calculates the ATF temperature based on the voltage signal.

DTC Code
DTC Detection Condition
Trouble Area
P0712
No. 1 ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1 trip detection logic).
  1. Short in No. 1 ATF temperature sensor circuit
  2. No. 1 ATF temperature sensor (No. 1 transmission wire)
  3. ECM
P0713
When 15 min. or more have elapsed after engine is started, No. 1 ATF temperature sensor resistance is more than 156 kΩ for 0.5 sec. or more (1 trip detection logic).
  1. Open in No. 1 ATF temperature sensor circuit
  2. No. 1 ATF temperature sensor (No. 1 transmission wire)
  3. ECM

MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature sensor circuit. If the resistance value of the ATF temperature sensor is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF temperature sensor or wiring. The ECM will illuminate the MIL and store the DTC.

HINT:
  1. *1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.
  2. *2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.
  3. The ATF temperature can be checked on the intelligent tester display.


WIRING DIAGRAM


C155188E25


INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the intelligent tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. Equal to ambient temperature while engine is cold
    If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.

    HINT:
    When DTC P0712 is output and the intelligent tester output is 150°C (302°F) or more, there is a short circuit.
    When DTC P0713 is output and the intelligent tester output is -40°C (-40°F), there is an open circuit.
    Measure the resistance between terminal THO1 and the body ground.


    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or more
    Short circuit

1.INSPECT NO. 1 TRANSMISSION WIRE (NO. 1 ATF TEMPERATURE SENSOR)


    C214326E31
  1. Disconnect the D41 No. 1 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (OT-) - 9 (OT+)
    Always
    79 Ω to 156 kΩ
    1 (OT-) - Body ground
    Always
    10 kΩ or higher
    9 (OT+) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range at one of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

    Standard Resistance:
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5 to 8 kΩ
    25°C (77°F)
    2.5 to 4.5 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ

Text in Illustration 
*a
Component without harness connected
(No. 1 Transmission Wire)


NG
REPAIR OR REPLACE NO. 1 ATF TEMPERATURE SENSOR (NO. 1 TRANSMISSION WIRE) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)


    C219456E02
  1. Disconnect the D56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D56-122 (THO1) - D56-98 (ETHA)
    Always
    79 Ω to 156 kΩ
    D56-122 (THO1) - Body ground
    Always
    10 kΩ or higher
    D56-98 (ETHA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)