Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0342    Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0343    Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)

DTC    P0345    Camshaft Position Sensor "A" Circuit (Bank 2)

DTC    P0347    Camshaft Position Sensor "A" Circuit Low Input (Bank 2)

DTC    P0348    Camshaft Position Sensor "A" Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (VV1, 2 signal) consists of a magnet and MRE (Magnet Resistance Element).
The intake camshaft has a sensor plate with 3 teeth on its outer circumference. When the intake camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0340
P0345
When either condition below is met:
  1. Input voltage to ECM remains at less than 0.3 V, or more than 4.7 V for 4 seconds when 2 or more seconds have elapsed after turning ignition switch to ON
    (1 trip detection logic)
  2. No VVT sensor signal to ECM during cranking
    (2 trip detection logic)
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Intake camshaft
  4. Jumped tooth of timing chain for intake camshaft
  5. ECM
P0342
P0347
Output voltage of VVT sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Intake camshaft
  4. Jumped tooth of timing chain for intake camshaft
  5. ECM
P0343
P0348
Output voltage of VVT sensor more than 4.7 V for 4 seconds
(1 trip detection logic)
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Intake camshaft
  4. Jumped tooth of timing chain for intake camshaft
  5. ECM

  1. A211720E02
    Reference: Inspection using an oscilloscope

    Standard:

    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    D56-110 (NE+) - D56-111 (NE-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown
    D56-92 (VV1+) - D56-91 (VV1-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown
    D56-87 (VV2+) - D56-88 (VV2-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown

    HINT:
    VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM


A179939E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
A186169E02
  1. Disconnect the VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.0 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM)


    A165015E05
  1. Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D22-1 (VVL+) - D56-92 (VV1+)
    Always
    Below 1 Ω
    D22-2 (VVL-) - D56-91 (VV1-)
    Always
    Below 1 Ω
    D23-1 (VVR+) - D56-87 (VV2+)
    Always
    Below 1 Ω
    D23-2 (VVR-) - D56-88 (VV2-)
    Always
    Below 1 Ω
    D22-1 (VVL+) or D56-92 (VV1+) - Body ground
    Always
    10 kΩ or higher
    D22-2 (VVL-) or D56-91 (VV1-) - Body ground
    Always
    10 kΩ or higher
    D23-1 (VVR+) or D56-87 (VV2+) - Body ground
    Always
    10 kΩ or higher
    D23-2 (VVR-) or D56-88 (VV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)


    BR03795E17
  1. Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4.INSPECT INTAKE CAMSHAFT (TEETH)
  1. Check the teeth of the camshaft.

    OK:
    Teeth do not have any cracks or deformation.



NG
REPLACE INTAKE CAMSHAFT (Click here)
OK


5.REPLACE VVT SENSOR
  1. Replace the VVT sensor (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear DTCs.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0340, P0342, P0343, P0345, P0347 or P0348 are output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END