Home › Drivetrain · AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > Transmission Control Switch Circuit

for Preparation Click here


DESCRIPTION

When moving the shift lever to S using the transmission control switch, it is possible to switch the shift range among "1" (1st range) and "6" (6th range).
Shifting to "+" once raises the shift range by one, and shifting to "-" lowers the shift range by one.

WIRING DIAGRAM


C179318E02


INSPECTION PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH


    C146679E13
  1. Disconnect the H31 transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IG) - 7 (S)
    Shift lever in S, "+" and "-"
    Below 1 Ω
    2 (SFTU) - 5 (E)
    Shift lever continuously in "+"
    (Up-shift)
    Below 1 Ω
    1 (SFTD) - 5 (E)
    Shift lever continuously in "-"
    (Down-shift)
    Below 1 Ω
    3 (IG) - 7 (S)
    Shift lever not in S, "+" and "-"
    10 kΩ or higher
    2 (SFTU) - 5 (E)
    Shift lever in S
    10 kΩ or higher
    1 (SFTD) - 5 (E)
    Shift lever in S
    10 kΩ or higher



NG
REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)


    C146729E20
  1. Disconnect the H31 transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H31-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H31-5 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)


    C159423E50
  1. Disconnect the A27 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A27-25 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever in S, "+" and "-"
    11 to 14 V
    1. Ignition switch ON
    2. Shift lever not in S, "+" and "-"
    Below 1 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A27-38 (SFTU) - Body ground
    Shift lever continuously in "+"
    (Up-shift)
    Below 1 Ω
    A27-27 (SFTD) - Body ground
    Shift lever continuously in "-"
    (Down-shift)
    Below 1 Ω
    A27-38 (SFTU) - Body ground
    Shift lever in S
    10 kΩ or higher
    A27-27 (SFTD) - Body ground
    Shift lever in S
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)