Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

  1. If the manual UP/DOWN function does not operate, there may be a malfunction in the power window regulator master switch, the power window regulator motor, the harness and connector.

WIRING DIAGRAM


B219835E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK LIN COMMUNICATION SYSTEM
  1. Check for LIN communication system DTCs related to the power window control system (Click here).

    OK:
    LIN communication system DTCs are not output.



NG
GO TO LIN COMMUNICATION SYSTEM (Click here)
OK


2.CHECK DTC (B2312)
  1. Check if DTC B2312 is output (Click here).

    OK:
    DTC B2312 is not output.



NG
GO TO DTC (B2312) (Click here)
OK


3.READ VALUE USING INTELLIGENT TESTER (D-DOOR MOTOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / D-Door Motor / Data List.

  1. According to the display on the intelligent tester, read the "Data List".

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Up SW
    Driver side power window MANUAL UP switch signal / ON or OFF
    ON: Driver side power window manual UP switch operated
    OFF: Driver side power window switch not operated
    -
    D Door P/W Down SW
    Driver side power window MANUAL DOWN switch signal / ON or OFF
    ON: Driver side power window manual DOWN switch operated
    OFF: OFF: Driver side power window switch not operated
    -

OK:
The intelligent tester display changes normally when master switch is operated.



NG
Go to step 4
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - BATTERY AND BODY GROUND)


    B178353E03
  1. Disconnect the M2 power window regulator master switch connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M2-3 (B) - Body ground
    Always
    11 to 14 V
    M2-13 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR LH - BATTERY AND BODY GROUND)


    B180291E08
  1. Disconnect the M3 front power window regulator motor LH connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    M3-2(B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M3-1(GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - FRONT POWER WINDOW MOTOR LH)
B191453E01
  1. Disconnect the M2 power window regulator master switch connector.

  1. Disconnect the M3 front power window regulator motor LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-4 (UP) - M3-10 (UP)
    Always
    Below 1 Ω
    M2-5 (DOWN) - M3-7 (DOWN)
    Always
    Below 1 Ω
    M2-4 (UP) - Body ground
    Always
    10 kΩ or higher
    M2-5 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    B194348E02
  1. Remove the front power window regulator motor LH (Click here).

  1. Apply positive (+) battery voltage to the connector terminal 2 (B).

    NOTICE:
    1. Do not apply positive (+) battery voltage to any terminals except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.
    2. Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

  1. Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) / 10 (UP).

  1. Check that the motor gear rotates smoothly as follows.

    OK:

    Measurement Condition
    Specified Condition
    Battery positive (+) → 2 (B)
    Battery negative (-) → (-): 1 (GND) (3 sec. or more) → 1 (GND) and 10 (UP) (within 1 sec.) → 1 (GND) (within 1 sec.) → 1 (GND) and 10 (UP)
    Motor gear rotates clockwise
    Battery positive (+) → 2 (B)
    Battery negative (-): 1 (GND) (3 sec. or more) → 1 (GND) and 7 (DOWN) (within 1 sec.) → 1 (GND) (within 1 sec.) → 1 (GND) and 7 (DOWN)
    Motor gear rotates counterclockwise



NG
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)