Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > Engine does not Start but Initial Combustion Occurs

for Preparation Click here


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM


B365295E05


INSPECTION PROCEDURE

NOTICE:
  1. If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
  2. When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC is not output.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Read the Data List according to the display on the GTS.

    Engine and ECT 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Immobiliser Fuel Cut
    Status of immobiliser system fuel cut / OFF/ON
    ON: Immobiliser fuel cut on
    OFF: Immobiliser fuel cut off
    -

    OK:
    The item in the Data List indicates "OFF".



NG
Go to step 4
OK

GO TO SFI SYSTEM (Click here)  

4.CHECK WHETHER ENGINE STARTS
  1. Using a registered key, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.

    Result 
    Result
    Proceed to
    Engine can be started
    A
    Engine cannot be started
    B



B
Go to step 5
A

USE SIMULATION METHOD TO CHECK (Click here)  

5.REGISTER ECU COMMUNICATION ID
  1. Register the communication ID between the transponder key ECU assembly and ECM.

    HINT:
    Refer to Service Bulletin.


NEXT


6.CHECK WHETHER ENGINE STARTS
  1. Using a registered key, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.

    Result 
    Result
    Proceed to
    Engine can be started
    A
    Engine cannot be started
    B



B
Go to step 7
A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE) 

7.REPLACE ECM
  1. Temporarily replace the ECM with a new or known good one (Click here).


NEXT


8.CHECK WHETHER ENGINE STARTS
  1. Using a registered key, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.



NG
Go to step 9
OK

END (ECM WAS DEFECTIVE) 

9.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
  1. Disconnect the H32 transponder key ECU assembly connector.

  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H32-13 (EFIO) - A27-40 (IMI)
    Always
    Below 1 Ω
    H32-12 (EFII) - A27-29 (IMO)
    Always
    Below 1 Ω
    H32-13 (EFIO) - Body ground
    Always
    10 kΩ or higher
    H32-12 (EFII) - Body ground
    Always
    10 kΩ or higher
    A27-40 (IMI) - Body ground
    Always
    10 kΩ or higher
    A27-29 (IMO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly with a new one.

    HINT:
    Refer to Service Bulletin.

    NOTICE:
    Key ID code registration is necessary when replacing the transponder key ECU assembly. Refer to Service Bulletin.

  1. Using a registered key, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

    OK:
    Engine starts normally.



NG
GO TO SFI SYSTEM (Click here)
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)