Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

DTC    B2610    Tilt Position Sensor or Tilt Motor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and outputs a signal to the CPU based on that tilt.

C152160E03

HINT:
Limit positions can be confirmed on the screen of the intelligent tester.


DTC Code
Detection Condition
Trouble Area
B2610
Tilt operation stops within the operation range while operating.
  1. Harness or connector
  2. Tilt position sensor or tilt motor
  3. Multiplex tilt and telescopic ECU

WIRING DIAGRAM


C160342E02


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TILT UP/DOWN)
C106468E01
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the tilt up/down function operates normally.

    Tilt & Telescopic 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Tilt Operation
    Tilt operation
    UP/DOWN
    -

Result 
Result
Proceed to
Steering wheel does not tilt up (down).
A
Steering wheel tilts up (down).
B


B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)

C149089E13

  1. Disconnect the H57 multiplex tilt and telescopic ECU connector.

  1. Disconnect the H58 tilt motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H57-10 (TIM+) - H58-2 (TIM+)
    Always
    Below 1 Ω
    H57-1 (TIM-) - H58-1 (TIM-)
    Always
    Below 1 Ω
    H57-10 (TIM+) - Body ground
    Always
    10 kΩ or higher
    H57-1 (TIM-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT TILT MOTOR


    C179946E01
  1. Connect the positive (+) battery terminal to terminal 2 (TIM+) and the negative (-) battery terminal to terminal 1 (TIM-) of the tilt motor connector. Then confirm that the steering wheel tilts up.

    OK:
    The steering wheel tilts up.

  1. Connect the negative (-) battery terminal to terminal 2 (TIM+) and the positive (+) battery terminal to terminal 1 (TIM-) of the tilt motor connector. Then confirm that the steering wheel tilts down.

    OK:
    The steering wheel tilts down.



NG
REPLACE STEERING COLUMN ASSEMBLY (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)  

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)

C149089E14

  1. Disconnect the H57 multiplex tilt and telescopic ECU connector.

  1. Disconnect the H58 tilt motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H57-6 (VCI) - H58-4 (VCI)
    Always
    Below 1 Ω
    H57-7 (TIS) - H58-5 (TIS)
    Always
    Below 1 Ω
    H57-17 (E1) - H58-6 (E1)
    Always
    Below 1 Ω
    H57-6 (VCI) - Body ground
    Always
    10 kΩ or higher
    H57-7 (TIS) - Body ground
    Always
    10 kΩ or higher
    H57-17 (E1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)


    C149087E25
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H57-11 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)


    C149091E04
  1. Reconnect the H57 multiplex tilt and telescopic ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H58-4 (VCI) - H58-6 (E1)
    Ignition switch ON
    8 to 16 V
    H58-5 (TIS) - H58-6 (E1)
    Ignition switch ON
    8 to 16 V



NG
REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)
OK


7.INSPECT TILT POSITION SENSOR


    C149088E25
  1. Reconnect the H58 tilt motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H57-7 (TIS) - H57-17 (E1)
    Steering tilts up or tilts down
    8 to 16 V (Pulse HI)
    Below 1 V (Pulse LOW)



NG
REPLACE STEERING COLUMN ASSEMBLY (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)