Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

  1. If there is a short in a speaker circuit, the navigation receiver assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the navigation receiver assembly or speakers.
  3. If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


E259816E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPEAKERS)
  1. Disconnect the connectors from the navigation receiver assembly and speakers.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I41-1 (FR+) - L8-1
    Always
    Below 1 Ω
    I41-5 (FR-) - L8-2
    Always
    Below 1 Ω
    I41-1 (FR+) - I11-3 (TWR+)
    Always
    Below 1 Ω
    I41-5 (FR-) - I11-4 (TWR-)
    Always
    Below 1 Ω
    I41-2 (FL+) - M10-1
    Always
    Below 1 Ω
    I41-6 (FL-) - M10-2
    Always
    Below 1 Ω
    I41-2 (FL+) - I13-3 (TWL+)
    Always
    Below 1 Ω
    I41-6 (FL-) - I13-4 (TWL-)
    Always
    Below 1 Ω
    I42-1 (RR+) - N1-1
    Always
    Below 1 Ω
    I42-3 (RR-) - N1-2
    Always
    Below 1 Ω
    I42-1 (RR+) - O37-1 (+)
    Always
    Below 1 Ω
    I42-3 (RR-) - O37-2 (-)
    Always
    Below 1 Ω
    I42-2 (RL+) - N7-1
    Always
    Below 1 Ω
    I42-6 (RL-) - N7-2
    Always
    Below 1 Ω
    I42-2 (RL+) - O31-1 (+)
    Always
    Below 1 Ω
    I42-6 (RL-) - O31-2 (-)
    Always
    Below 1 Ω
    I41-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    I41-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    I41-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    I41-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    I42-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I42-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    I42-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I42-6 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E144966
  1. Disconnect the front No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E146506E26
  1. Disconnect the front No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    3 (TWL+) - 1 (+)
    Always
    Below 1 Ω
    4 (TWL-) - 2 (-)
    Always
    Below 1 Ω
    3 (TWL+) - 4 (TWL-)
    Always
    3.4 to 4.6 Ω
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    3 (TWR+) - 1 (+)
    Always
    Below 1 Ω
    4 (TWR-) - 2 (-)
    Always
    Below 1 Ω
    3 (TWR+) - 4 (TWR-)
    Always
    3.4 to 4.6 Ω

    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    E160614
  1. Disconnect the front No. 3 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    4 Ω



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)
  1. *1: for LH Side
  2. *2: for RH Side
  1. Disconnect the I13*1 and/or I11*2 front No. 2 speaker assembly connector.

  1. Disconnect the M1*1 and/or L1*2 front No. 3 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    I13-1 (+) - M1-3
    Always
    Below 1 Ω
    I13-2 (-) - M1-1
    Always
    Below 1 Ω
    I13-1 (+) - Body ground
    Always
    10 kΩ or higher
    I13-2 (-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    I11-1 (+) - L1-3
    Always
    Below 1 Ω
    I11-2 (-) - L1-1
    Always
    Below 1 Ω
    I11-1 (+) - Body ground
    Always
    10 kΩ or higher
    I11-2 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT QUARTER SIDE SPEAKER ASSEMBLY


    E146506E27
  1. Disconnect the quarter side speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (+)
    Always
    Below 1 Ω
    2 (-) - 4 (-)
    Always
    Below 1 Ω
    1 (+) - 2 (-)
    Always
    4 Ω



NG
REPLACE QUARTER SIDE SPEAKER ASSEMBLY (Click here)
OK


7.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E160614
  1. Disconnect the rear No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    4 Ω



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (QUARTER SIDE SPEAKER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)
  1. *1: for LH Side
  2. *2: for RH Side
  1. Disconnect the O31*1 and/or O37*2 quarter side speaker assembly connector.

  1. Disconnect the N8*1 and/or N2*2 rear No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    O31-3 (+) - N8-3
    Always
    Below 1 Ω
    O31-4 (-) - N8-1
    Always
    Below 1 Ω
    O31-3 (+) - Body ground
    Always
    10 kΩ or higher
    O31-4 (-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    O37-3 (+) - N2-3
    Always
    Below 1 Ω
    O37-4 (-) - N2-1
    Always
    Below 1 Ω
    O37-3 (+) - Body ground
    Always
    10 kΩ or higher
    O37-4 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    E144966
  1. Disconnect the rear No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY