DTC P2742 Transmission Fluid Temperature Sensor "B" Circuit Low Input |
DTC P2743 Transmission Fluid Temperature Sensor "B" Circuit High Input |
| No. 2 ATF Temperature Sensor State | Detection Condition | Symptom | Recovery Condition |
| Sensor is normal | ATF temperature more than 150°C (302°F) | ATF temperature warning light is illuminated or message is displayed in combination meter | ATF temperature less than 135°C (275°F)*1 |
| ATF temperature more than 130°C (266°F) | Shift point too high | ATF temperature less than 110°C (230°F) | |
| When the conditions (a) and (b) are satisfied. (a) ATF temperature more than 130°C (266°F) (b) Engine coolant temperature more than 95°C (203°F) | Lock-up at 3rd gear*2 | ATF temperature less than 110°C (230°F)*1 and engine coolant temperature more than 95°C (203°F) | |
| Sensor is short-circuited | Any conditions |
| Symptoms still occur |
| Engine coolant temperature more than 95°C (203°F) | Lock-up at 3rd gear*2 | Symptoms still occur |
| DTC Code | DTC Detection Condition | Trouble Area |
| P2742 | No. 2 ATF temperature sensor resistance is less than 25 Ω (0.046 V) for 0.5 seconds or more (1 trip detection logic). |
|
| P2743 | When 15 minutes or more have elapsed after engine is started, No. 2 ATF temperature sensor resistance is more than 156 kΩ (4.915 V) for 0.5 seconds or more (1 trip detection logic). |
|
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| A/T Oil Temperature 2 | No. 2 ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted. |
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 150°C (302°F) or more | Short circuit |
| 1.INSPECT NO. 1 TRANSMISSION WIRE (NO. 2 ATF TEMPERATURE SENSOR) |
![]() |
Disconnect the D41 No. 1 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (OT2-) - 10 (OT2+) | Always | 25 Ω to 156 kΩ |
| 2 (OT2-) - Body ground | Always | 10 kΩ or higher |
| 10 (OT2+) - Body ground | Always | 10 kΩ or higher |
| ATF temperature | Specified Condition |
| 10°C (50°F) | 5 to 8 kΩ |
| 25°C (77°F) | 2.5 to 4.5 kΩ |
| 110°C (230°F) | 0.22 to 0.28 kΩ |
| *a | Component without harness connected (No. 1 Transmission Wire) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM) |
![]() |
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D56-99 (THO2) - D56-98 (ETHA) | Always | 25 Ω to 156 kΩ |
| D56-99 (THO2) - Body ground | Always | 10 kΩ or higher |
| D56-98 (ETHA) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||